Comparison of Surface Roughness and Color Stability of Different Denture Characterizing Composite Resins: The Effect of Different Surface Treatments
Journal of Prosthodontics · 2023-04 · 32 (S1) · 53-60
DOI: 10.1111/jopr.13577 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 23.08.2022. Verfasst von Hatice Nalan Bozoğulları und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Alanya Alaaddin Keykubat University, Antalya, Turkey. Hauptthemen laut MEDLINE: Coffee, Composite Resins. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 56 Literaturangaben.
Abstract (Originalsprache)
Purpose
This study aimed to investigate the effect of surface treatment and type of composite resin material on the color stability and surface roughness of different denture characterizing composites. Materials and methods Two nanohybrids [Gradia Plus Gum, (GP) and SR Nexco Paste Gingiva, (SR)] and one microhybrid gingiva‐colored composite resin [Amaris Gingiva, (AG)] were investigated. A total of 120 disk‐shaped samples were prepared, 40 of each material. Samples were divided into two groups (n = 20) for each material according to the surface treatment applied: conventional polishing (control) and coated with a sealant in addition to the surface polishing. All groups were thermocycled. The surface roughness (Ra) was measured using a profilometer after thermal cycling. The samples were then divided into 2 subgroups (n = 10) and stored for 7 days in distilled water or coffee solution. Color differences (ΔE 00 ) were calculated with a spectrophotometer. Results were evaluated with Kruskal‐Wallis and Mann‐Whitney U statistical analysis.
Results
The type of denture characterizing composite material and surface treatment method revealed statistically significant differences for the ΔE 00 (after immersion both in coffee and distilled water) and the Ra values of denture characterizing composite ( p < 0.001 for both). All sealed groups showed significantly higher Ra than the all polished groups. Both in the polished groups and the sealant applied groups, the GP had the highest mean Ra values (0.29 ±0.05 μm and 0.47 ±0.09 μm, respectively). It was followed by SR (0.23 ±0.06 μm and 0.41 ±0.10 μm, respectively), and AG groups (0.20 ±0.06 μm and 0.39 ±0.09 μm, respectively). According to the mean ΔE 00 results, all composite groups showed significantly higher ΔE 00 values immersed in coffee solutions compared to distilled water. In coffee solutions, the highest ΔE 00 was observed in the polished GP (1.90 ±0.40), and the lowest ΔE 00 was observed in the polished SR (0.97 ±0.36). The sealed groups showed higher ΔE 00 than the polished groups, except for GP.
Conclusions
The surface roughness value of sealant applied groups were significantly higher than those of the polished groups. The surface sealant application significantly increased the staining of all composite groups compared to conventional polishing, except for GP.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Prosthodontics, Faculty of Dentistry, Alanya Alaaddin Keykubat University, Antalya, Turkey.
- Department of Prosthodontics, Faculty of Dentistry, Necmettin Erbakan University, Konya, Turkey.
- Department of Endodontics, Faculty of Dentistry, Alanya Alaaddin Keykubat University, Antalya, Turkey.
ORCID-Profile: Hatice Nalan Bozoğulları
Zitieren
APA
Bozoğulları, H. N., Büyükerkmen, E. B., & Büyüközer Özkan, H. (2023). Comparison of Surface Roughness and Color Stability of Different Denture Characterizing Composite Resins: The Effect of Different Surface Treatments. Journal of Prosthodontics, 32(S1), 53-60. https://doi.org/10.1111/jopr.13577
Vancouver
Bozoğulları HN, Büyükerkmen EB, Büyüközer Özkan H. Comparison of Surface Roughness and Color Stability of Different Denture Characterizing Composite Resins: The Effect of Different Surface Treatments. Journal of Prosthodontics. 2023;32(S1):53-60. doi:10.1111/jopr.13577
BibTeX
@article{Bozoullar2023,
author = {Bozoğulları, Hatice Nalan and Büyükerkmen, Emine Begüm and Büyüközer Özkan, Hatice},
title = {Comparison of Surface Roughness and Color Stability of Different Denture Characterizing Composite Resins: The Effect of Different Surface Treatments},
journal = {Journal of Prosthodontics},
year = {2023},
volume = {32},
number = {S1},
pages = {53--60},
doi = {10.1111/jopr.13577}
}
EUVIMED