EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Two‐Dimensional Accuracy of Provisional Laminate Veneers Designed Using Two Digital Smile Design Platforms and Fabricated by Additive and Subtractive Manufacturing

Murat Feriz iD, Zeliha Şanıvar Abbasgholizadeh iD, Yılmaz Umut Aslan iD, Yasemin Özkan iD

Journal of Esthetic and Restorative Dentistry · 2026-08 · 38 (8) · 1574-1585

DOI: 10.1111/jerd.70178 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Esthetic and Restorative Dentistry, online erschienen am 03.05.2026. Verfasst von Murat Feriz und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Marmara University, Istanbul, Türkiye. Hauptthemen laut MEDLINE: Dental Veneers, Smiling, Computer-Aided Design, Dental Prosthesis Design. Die Arbeit nennt 24 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Marmara Üniversitesi.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

To evaluate and compare the two‐dimensional (2D) accuracy of provisional laminate veneer restorations designed using two digital smile design platforms and fabricated through additive and subtractive manufacturing techniques within a standardized digital workflow. Materials and Methods This study included 25 participants for whom provisional laminate veneer restorations were digitally designed for the maxillary anterior region using two digital smile design platforms. Each digital design was subsequently fabricated using two manufacturing methods, additive manufacturing (stereolithography‐based printing) and subtractive manufacturing (milling), resulting in a total of 600 restorations. Standardized clinical photography protocols, including consistent camera positioning, fixed shooting distances, controlled lighting conditions, standardized patient positioning, and intraoral scanning protocols, were applied for data acquisition. Linear measurements were obtained from virtual designs and corresponding fabricated restorations. Measurement reliability was assessed using the intraclass correlation coefficient. Statistical analyses were performed to evaluate dimensional deviations and the effects of the software platform and fabrication method ( α = 0.05).

Results

Statistically significant differences were identified between virtual designs and fabricated restorations; however, the magnitude of these deviations remained small. The manufacturing method demonstrated a greater influence on dimensional discrepancies than the digital smile design software platform. No statistically significant differences were observed between the two software platforms when standardized digital workflow conditions were applied. Measurement reliability analysis revealed high intraclass correlation coefficients.

Conclusions

The fabrication method significantly influenced the 2D accuracy of provisional laminate veneer restorations, with additively manufactured restorations demonstrating smaller deviations in linear measurements compared to milled restorations. No significant difference was observed between the digital smile design software platforms.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental VeneersSmilingComputer-Aided DesignDental Prosthesis DesignHumansFemaleEsthetics, Dental

Stichwörter der Autor:innen

additive manufacturingdigital prosthodontic workflowdigital smile designprovisional laminate veneerssubtractive manufacturingtwo‐dimensional accuracy

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Dentistry, Marmara University, Istanbul, Türkiye.
  • Institute of Health Sciences, Marmara University, Istanbul, Türkiye.

ORCID-Profile: Murat Feriz, Zeliha Şanıvar Abbasgholizadeh, Yılmaz Umut Aslan, Yasemin Özkan

Förderung

  • Marmara Üniversitesi

Zitieren

APA

Feriz, M., Abbasgholizadeh, Z. Ş., Aslan, Y. U., & Özkan, Y. (2026). Two‐Dimensional Accuracy of Provisional Laminate Veneers Designed Using Two Digital Smile Design Platforms and Fabricated by Additive and Subtractive Manufacturing. Journal of Esthetic and Restorative Dentistry, 38(8), 1574-1585. https://doi.org/10.1111/jerd.70178

Vancouver

Feriz M, Abbasgholizadeh ZŞ, Aslan YU, Özkan Y. Two‐Dimensional Accuracy of Provisional Laminate Veneers Designed Using Two Digital Smile Design Platforms and Fabricated by Additive and Subtractive Manufacturing. Journal of Esthetic and Restorative Dentistry. 2026;38(8):1574-1585. doi:10.1111/jerd.70178

BibTeX
@article{Feriz2026,
  author = {Feriz, Murat and Abbasgholizadeh, Zeliha Şanıvar and Aslan, Yılmaz Umut and Özkan, Yasemin},
  title = {Two‐Dimensional Accuracy of Provisional Laminate Veneers Designed Using Two Digital Smile Design Platforms and Fabricated by Additive and Subtractive Manufacturing},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2026},
  volume = {38},
  number = {8},
  pages = {1574--1585},
  doi = {10.1111/jerd.70178}
}
Kostenlos starten →