EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Stainability and translucency of potassium aluminum sulfate applied computer‐aided design and computer‐aided manufacturing materials after coffee thermocycling

Rafat Sasany, Mustafa Borga Donmez, Marcella Silva de Paula, Çiğdem Kahveci, Gözlem Ceylan, Burak Yilmaz, Gülce Çakmak

Journal of Esthetic and Restorative Dentistry · 2024

DOI: 10.1111/jerd.13154 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Esthetic and Restorative Dentistry, 2024. Verfasst von Rafat Sasany und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Biruni University, İstanbul, Turkey. Hauptthemen laut MEDLINE: Dental Porcelain, Coffee, Alum Compounds. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

The purpose of this in vitro study was to evaluate the effect of potassium aluminum sulfate (alum) application on the stainability and translucency of computer‐aided design and computer‐aided manufacturing (CAD‐CAM) materials after coffee thermocycling (CTC). Materials and Methods Disk‐shaped specimens (Ø10 × 1 mm; N = 200) were fabricated by using additively (Crowntec [CT] and Varseo Smile Crown Plus [VS]) and subtractively manufactured (Brilliant Crios [RCR], CEREC Block [FC], and Vita Enamic [VE]) CAD‐CAM materials and polished. All specimens were randomly divided into two groups as alum applied and control ( n = 10). All specimens were then subjected to CTC (10,000 cycles at 5–55°C) and color coordinates were measured at each time interval. Color differences (Δ E 00 ) and relative translucency parameters (RTPs) were calculated and the data were statistically analyzed ( a = 0.05).

Results

Among tested time intervals, alum applied specimens had their lowest Δ E 00 after alum application ( p ≤ 0.006), except for FC ( p = 0.177). In addition, alum applied RCR had lower Δ E 00 values than its control specimens ( p = 0.029). Alum applied specimens had their lowest RTP after CTC ( p < 0.001) and alum application decreased the RTP of CT ( p = 0.010). CTC reduced the RTP of all materials in control groups ( p < 0.001). Alum applied CT had higher RTP than its control specimens ( p = 0.049).

Conclusions

Alum application's effect on color change varied depending on the material and alum mostly resulted in clinically acceptable changes in translucency. CTC led to unacceptable color and translucency changes based on previously reported threshold values. Clinical Significance Optical properties of CAD‐CAM materials and the sustainability of these properties over time is critical for longevity. Alum may improve the color stability of reinforced composite resin when subjected to long‐term coffee consumption.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental PorcelainCoffeeAlum CompoundsColorMaterials TestingSurface PropertiesCeramicsComputer-Aided Design

Stichwörter der Autor:innen

CAD-CAMcoffee thermocyclingpotassium aluminum sulfatestainabilitytranslucency

Substanzen

Dental PorcelainCoffeealuminum sulfateAlum Compounds

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Dentistry, Biruni University, İstanbul, Turkey.
  • Department of Prosthodontics, Faculty of Dentistry, Istinye University, İstanbul, Turkey.
  • Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland.
  • Department of Prevention and Oral Rehabilitation, Universidade Federal de Goiás (UFG), Goiânia, Brazil.
  • Ordu Oral and Dental Health Center, Ordu, Turkey.
  • Department of Prosthodontics, Faculty of Dentistry, Ondokuz Mayıs University, Samsun, Turkey.

Zitieren

APA

Sasany, R., Donmez, M. B., de Paula, M. S., Kahveci, Ç., Ceylan, G., Yilmaz, B., & Çakmak, G. (2024). Stainability and translucency of potassium aluminum sulfate applied computer‐aided design and computer‐aided manufacturing materials after coffee thermocycling. Journal of Esthetic and Restorative Dentistry. https://doi.org/10.1111/jerd.13154

Vancouver

Sasany R, Donmez MB, de Paula MS, Kahveci Ç, Ceylan G, Yilmaz B, et al. Stainability and translucency of potassium aluminum sulfate applied computer‐aided design and computer‐aided manufacturing materials after coffee thermocycling. Journal of Esthetic and Restorative Dentistry. 2024. doi:10.1111/jerd.13154

BibTeX
@article{Sasany2024,
  author = {Sasany, Rafat and Donmez, Mustafa Borga and de Paula, Marcella Silva and Kahveci, Çiğdem and Ceylan, Gözlem and Yilmaz, Burak and Çakmak, Gülce},
  title = {Stainability and translucency of potassium aluminum sulfate applied computer‐aided design and computer‐aided manufacturing materials after coffee thermocycling},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2024},
  doi = {10.1111/jerd.13154}
}
Kostenlos starten →