EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

From rapid prototyping to rapid firing: on the feasibility of high‐speed production for complex BaTiO 3 components

Subhadip Bhandari, Ondrej Hanzel, Peter Veteška, Marián Janek, Emanuele De Bona, Vincenzo M. Sglavo, Mattia Biesuz, Giorgia Franchin

Journal of the American Ceramic Society · 2024-10 · 107 (10) · 6562-6573

DOI: 10.1111/jace.19950 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of the American Ceramic Society, online erschienen am 14.06.2024. Verfasst von Subhadip Bhandari und 7 weiteren Autor:innen. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministero dell'Università e della Ricerca, Ministero dello Sviluppo Economico.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Direct ink writing (DIW) is an attractive additive manufacturing (AM) technology because of its simplicity, production speed, and feedstock flexibility; in addition, the use of a limited amount of binder makes the subsequent thermal debinding process easy. Nevertheless, the conventional approach to debind and sinter AMed components remains extremely slow, representing a bottleneck in the manufacturing process. In order to address such limitation, we explored different rapid sintering strategies: ultrafast high‐temperature sintering (UHS), pressureless spark plasma sintering (P‐SPS), and fast firing (FF), for the densification of BaTiO 3 components fabricated by DIW, one of the widely used lead‐free piezoceramics. All sintering technologies allow debinding and sintering of crack‐free components in a few minutes instead of several hours. The final density and microstructure are strongly dependent on the sintering atmosphere (inert for UHS and P‐SPS, air for FF) and a maximum relative density of only ≈72% was obtained when firing occurred in an inert environment, irrespective of the sintering technique (UHS and P‐SPS). An undesired phase transition from tetragonal to hexagonal BaTiO 3 was also observed upon UHS and ‐PSPS. On the contrary, FF in air yielded a density of about 95% in a few minutes while maintaining the desired tetragonal polymorph. The results provide proof of feasibility for rapid processing of BaTiO 3 components obtained by DIW.

Förderung

  • Ministero dell'Università e della Ricerca
  • Ministero dello Sviluppo Economico

Zitieren

APA

Bhandari, S., Hanzel, O., Veteška, P., Janek, M., Bona, E. D., Sglavo, V. M., Biesuz, M., & Franchin, G. (2024). From rapid prototyping to rapid firing: on the feasibility of high‐speed production for complex BaTiO 3 components. Journal of the American Ceramic Society, 107(10), 6562-6573. https://doi.org/10.1111/jace.19950

Vancouver

Bhandari S, Hanzel O, Veteška P, Janek M, Bona ED, Sglavo VM, et al. From rapid prototyping to rapid firing: on the feasibility of high‐speed production for complex BaTiO 3 components. Journal of the American Ceramic Society. 2024;107(10):6562-6573. doi:10.1111/jace.19950

BibTeX
@article{Bhandari2024,
  author = {Bhandari, Subhadip and Hanzel, Ondrej and Veteška, Peter and Janek, Marián and Bona, Emanuele De and Sglavo, Vincenzo M. and Biesuz, Mattia and Franchin, Giorgia},
  title = {From rapid prototyping to rapid firing: on the feasibility of high‐speed production for complex BaTiO 3 components},
  journal = {Journal of the American Ceramic Society},
  year = {2024},
  volume = {107},
  number = {10},
  pages = {6562--6573},
  doi = {10.1111/jace.19950}
}
Kostenlos starten →