EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of sintering temperature on the dielectric properties of 3D‐printed alumina (Al 2 O 3 ) in the W‐band

Kai‐Daniel Jenkel, Jesús Sánchez‐Pastor, Mohammad Mahdi Baloochian, Rolf Jakoby, Masoud Sakaki, Alejandro Jiménez‐Sáez, Niels Benson

Journal of the American Ceramic Society · 2024-04 · 107 (4) · 2494-2503

DOI: 10.1111/jace.19597 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of the American Ceramic Society, online erschienen am 13.12.2023. Verfasst von Kai‐Daniel Jenkel und 6 weiteren Autor:innen. Die Arbeit wurde bisher 21-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deutsche Forschungsgemeinschaft.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This contribution discusses the impact of sintering temperatures on dielectric properties of 3D‐printed alumina (Al 2 O 3 ) in the W‐band, by evaluating high quality factor (− Q ) resonators integrated in a 2D photonic crystal structure. By varying the sintering temperature of the lithography‐based ceramic manufactured (LCM) samples, the microstructure of the material can be defined, which has a direct impact on the dielectric permittivity and material losses. Using a highly accurate photonic crystal structure, with a dimensional variation below 2% from print to print, an accurate extraction and evaluation of the dielectric material properties could be achieved. The relative permittivity of the alumina was tuned from 4.4 at 1250°C to 9.2 at 1650°C, whereas the observed change in dielectric losses was moderate. The maximum in observed dielectric loss for samples sintered at the lowest evaluated temperature, only yields an average value of 30 × 10 −4 . This demonstrates the versatility of the LCM technology for mm‐ and sub‐mm‐wave applications and its possibilities for material tuneability.

Förderung

  • Deutsche Forschungsgemeinschaft

Zitieren

APA

Jenkel, K., Sánchez‐Pastor, J., Baloochian, M. M., Jakoby, R., Sakaki, M., Jiménez‐Sáez, A., & Benson, N. (2024). Effect of sintering temperature on the dielectric properties of 3D‐printed alumina (Al 2 O 3 ) in the W‐band. Journal of the American Ceramic Society, 107(4), 2494-2503. https://doi.org/10.1111/jace.19597

Vancouver

Jenkel K, Sánchez‐Pastor J, Baloochian MM, Jakoby R, Sakaki M, Jiménez‐Sáez A, et al. Effect of sintering temperature on the dielectric properties of 3D‐printed alumina (Al 2 O 3 ) in the W‐band. Journal of the American Ceramic Society. 2024;107(4):2494-2503. doi:10.1111/jace.19597

BibTeX
@article{Jenkel2024,
  author = {Jenkel, Kai‐Daniel and Sánchez‐Pastor, Jesús and Baloochian, Mohammad Mahdi and Jakoby, Rolf and Sakaki, Masoud and Jiménez‐Sáez, Alejandro and Benson, Niels},
  title = {Effect of sintering temperature on the dielectric properties of 3D‐printed alumina (Al 2 O 3 ) in the W‐band},
  journal = {Journal of the American Ceramic Society},
  year = {2024},
  volume = {107},
  number = {4},
  pages = {2494--2503},
  doi = {10.1111/jace.19597}
}
Kostenlos starten →