EUVIMEDEUVIMED entdecken
Crossref

Evaluation of 316L stainless mill additives on microstructure and alkali corrosive behavior of enamel coatings

Hao Hong, Wensheng Li, Cuixia Li, Ting Zhang, Chunzhi Zhang, Elena Yatsenko, Jinquan Sun, Shang Tang

Journal of the American Ceramic Society · 2023-08 · 106 (8) · 4617-4633

DOI: 10.1111/jace.19115 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of the American Ceramic Society, online erschienen am 07.04.2023. Verfasst von Hao Hong und 7 weiteren Autor:innen. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 35 Literaturangaben. Gefördert von: National Natural Science Foundation of China.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Excellent chemical stability, good corrosion resistance, and compositional controllability make vitrified enamel promising coating materials. The corrosion resistance of the [–Si–O–]/[–Si–O–Al–]‐based enamel coatings decreases in alkaline environments, whereas can be improved by incorporating metal oxides, such as ZrO 2 and SnO 2 . The introduction of these oxides results in an increase in the sintering temperature and a decrease in the toughness of the coatings. It was observed that the corrosion resistance of the coatings in an alkaline medium could be improved using metal powder‐based additives without increasing the sintering temperature and affecting the mechanical properties of the coatings. We used powdered 316L stainless steel as the mill additive, and the effects of this additive on the structure and alkali corrosion resistance of the vitrified enamel coatings were studied. Results indicate that the addition of an appropriate quantity of the additive (4 wt.%) improves the extent of gas consumption during the enamel sintering, decreases the degree of porosity and the size of the pores. Furthermore, the mechanical properties of the skeleton formed between the pores could be improved, because blocklike corrosion products are not peeled off, which increases the corrosion resistance of the coatings. The corrosion products, such as Ca‐based compounds, block the corrosion holes, resulting in a decrease in the corrosion rate also.

Förderung

  • National Natural Science Foundation of China

Zitieren

APA

Hong, H., Li, W., Li, C., Zhang, T., Zhang, C., Yatsenko, E., Sun, J., & Tang, S. (2023). Evaluation of 316L stainless mill additives on microstructure and alkali corrosive behavior of enamel coatings. Journal of the American Ceramic Society, 106(8), 4617-4633. https://doi.org/10.1111/jace.19115

Vancouver

Hong H, Li W, Li C, Zhang T, Zhang C, Yatsenko E, et al. Evaluation of 316L stainless mill additives on microstructure and alkali corrosive behavior of enamel coatings. Journal of the American Ceramic Society. 2023;106(8):4617-4633. doi:10.1111/jace.19115

BibTeX
@article{Hong2023,
  author = {Hong, Hao and Li, Wensheng and Li, Cuixia and Zhang, Ting and Zhang, Chunzhi and Yatsenko, Elena and Sun, Jinquan and Tang, Shang},
  title = {Evaluation of 316L stainless mill additives on microstructure and alkali corrosive behavior of enamel coatings},
  journal = {Journal of the American Ceramic Society},
  year = {2023},
  volume = {106},
  number = {8},
  pages = {4617--4633},
  doi = {10.1111/jace.19115}
}
Kostenlos starten →