EUVIMEDEUVIMED entdecken
Randomisierte kontrollierte StudieOpen Access · CC BY-NC-ND 4.0

Evaluation of 3D ‐Printed Models in Dentoalveolar Trauma Simulation: A Randomized Trial in Undergraduate Dental Training

Cemre Koç iD, Bahar Melis Akyıldız iD, Ayşe Taş

Dental Traumatology · 2025

DOI: 10.1111/edt.13065 ↗

Kurz gefasst

Randomisierte kontrollierte Studie in der Zeitschrift Dental Traumatology, 2025. Verfasst von Cemre Koç und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Endodontics, Faculty of Dentistry, Aydın Adnan Menderes University, Aydın, Türkiye. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Education, Dental, Students, Dental, Simulation Training. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background/Aim This study evaluated the impact of simulation training using 3D‐printed models on anxiety, stress, self‐confidence, and knowledge among dental students managing dentoalveolar trauma. Material and Methods This prospective, randomized controlled trial was conducted with fourth‐year dental students, who were assigned to two groups. The control group received theoretical instruction only, while the experimental group received theoretical instruction combined with simulation training using 3D‐printed models. Prior to the simulation training (T1), all students attended a 30‐min lecture covering four trauma types: uncomplicated crown fracture, complicated crown fracture, intrusive luxation, and avulsion. At T1, all students completed questionnaires and a visual analog scale (VAS) to assess anxiety (STAI Trait [T] and State [S]), stress, self‐confidence, and knowledge. Following this, only the experimental group participated in the simulation training. At T2 (two weeks later), both groups completed the same questionnaires and VAS assessments. The control group participated in the simulation training after the study concluded. Statistical analyses were conducted using the chi‐square test, McNemar test, independent samples t ‐test, Mann–Whitney U test, paired samples t ‐test, and Wilcoxon test, with statistical significance set at p ≤ 0.05.

Results

Each group comprised 34 students, with no significant baseline differences in STAI‐T scores ( p = 0.57). At T1, no significant differences were observed between groups in STAI‐S, VAS, confidence, or knowledge scores. At T2, the experimental group showed significantly higher self‐confidence and knowledge scores than the control group ( p < 0.001), although stress and anxiety scores remained comparable ( p > 0.05). Within the experimental group, anxiety, stress, self‐confidence, and knowledge scores improved significantly between T1 and T2.

Conclusions

Incorporating 3D‐printed models into simulation training significantly enhanced students' self‐confidence and knowledge in dentoalveolar trauma management, underscoring the value of simulation‐based training for improved educational outcomes.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalEducation, DentalStudents, DentalSimulation TrainingTooth InjuriesModels, DentalHumansProspective StudiesFemaleMaleClinical CompetenceSurveys and QuestionnairesSelf Concept

Stichwörter der Autor:innen

dental educationdental studentssimulation trainingtrauma

Autor:innen und Institutionen

  • Department of Endodontics, Faculty of Dentistry, Aydın Adnan Menderes University, Aydın, Türkiye.
  • Department of Pediatric Dentistry, Faculty of Dentistry, Aydın Adnan Menderes University, Aydın, Türkiye.
  • Department of Public Health, Faculty of Medicine, Adıyaman University, Adıyaman, Türkiye.

ORCID-Profile: Cemre Koç, Bahar Melis Akyıldız

Zitieren

APA

Koç, C., Akyıldız, B. M., & Taş, A. (2025). Evaluation of 3D ‐Printed Models in Dentoalveolar Trauma Simulation: A Randomized Trial in Undergraduate Dental Training. Dental Traumatology. https://doi.org/10.1111/edt.13065

Vancouver

Koç C, Akyıldız BM, Taş A. Evaluation of 3D ‐Printed Models in Dentoalveolar Trauma Simulation: A Randomized Trial in Undergraduate Dental Training. Dental Traumatology. 2025. doi:10.1111/edt.13065

BibTeX
@article{Ko2025,
  author = {Koç, Cemre and Akyıldız, Bahar Melis and Taş, Ayşe},
  title = {Evaluation of 3D ‐Printed Models in Dentoalveolar Trauma Simulation: A Randomized Trial in Undergraduate Dental Training},
  journal = {Dental Traumatology},
  year = {2025},
  doi = {10.1111/edt.13065}
}
Kostenlos starten →