EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Non‐invasive oral implant position assessment: An ex vivo study using a 3D industrial scan as the reference model to mimic the clinical situation

Mihai Tarce iD, Kathrin Becker iD, Pierre Lahoud iD, Sohaib Shujaat, Reinhilde Jacobs iD, Marc Quirynen

Clinical Oral Implants Research · 2024

DOI: 10.1111/clr.14206 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Clinical Oral Implants Research, 2024. Verfasst von Mihai Tarce und 5 weiteren Autor:innen. Beteiligte Einrichtung: Division of Periodontology & Implant Dentistry, Faculty of Dentistry, The University of Hong Kong, Hong Kong SAR, China. Hauptthemen laut MEDLINE: Cone-Beam Computed Tomography, Imaging, Three-Dimensional, Cadaver, Dental Implants. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: Dentsply Sirona Implants.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Aim

To introduce an objective method to evaluate the accuracy of implant position assessment in partially edentulous patients by comparing different techniques (conventional impression, intraoral scan, CBCT) to a reference 3D model obtained with an industrial scanner, the latter mimicking the clinical situation. Materials and Methods Twenty‐nine implants were placed in four human cadaver heads using a fully guided flapless protocol. Implant position was assessed using (a) a conventional impression, (b) an intraoral scan, and (c) CBCT and compared to an industrial scan. Three‐dimensional models of intraoral scan body and implant were registered to the arch models and the deviation at implant shoulder, apex, and the angle of deviation were compared to each other as well as to the reference model.

Results

The three assessment techniques showed statistically significant deviations ( p < .01) from the industrial scan, for all measurements, with no difference between the techniques. The maximum deviation at the implant shoulder was 0.16 mm. At the implant apex this increased to 0.38 mm. The intraoral scan deviated significantly more than the CBCT (0.12 mm, p < .01) and the conventional impression (0.10 mm, p = .02). The maximum implant angle deviation was 1.0°. The intraoral scan deviated more than the conventional impression (0.3°, p = .02).

Conclusion

All assessment techniques deviated from the reference industrial scan, but the differences were relatively small. Intraoral scans were slightly less accurate than both conventional impressions and CBCT. Depending on the application, however, this inaccuracy may not be clinically relevant.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Cone-Beam Computed TomographyImaging, Three-DimensionalCadaverDental ImplantsDental Impression TechniqueHumansDental Implantation, EndosseousModels, DentalJaw, Edentulous, Partially

Stichwörter der Autor:innen

CBCTaccuracyconventional impressionimplant positionintraoral scanoral implant

Substanzen

Dental Implants

Autor:innen und Institutionen

  • Division of Periodontology & Implant Dentistry, Faculty of Dentistry, The University of Hong Kong, Hong Kong SAR, China.
  • Periodontology and Oral Microbiology, Department of Oral Health Sciences, Faculty of Medicine, KU Leuven, Leuven, Belgium.
  • Charité- Universitätsmedizin Berlin, Corporate member of Freie Universität Berlin and Humboldt-Universität zu Berlin, Department of Orthodontics and Dentofacial Orthopedics, Berlin, Germany.
  • OMFS-IMPATH Research Group, Department of Imaging and Pathology, Faculty of Medicine, KU Leuven, Leuven, Belgium.
  • Department of Oral & Maxillofacial Surgery, University Hospitals Leuven, Leuven, Belgium.
  • King Abdullah International Medical Research Center, Department of Maxillofacial Surgery and Diagnostic Sciences, College of Dentistry, King Saud bin Abdulaziz University for Health Sciences, Ministry of National Guard…

ORCID-Profile: Mihai Tarce, Kathrin Becker, Pierre Lahoud, Reinhilde Jacobs

Förderung

  • Dentsply Sirona Implants

Zitieren

APA

Tarce, M., Becker, K., Lahoud, P., Shujaat, S., Jacobs, R., & Quirynen, M. (2024). Non‐invasive oral implant position assessment: An ex vivo study using a 3D industrial scan as the reference model to mimic the clinical situation. Clinical Oral Implants Research. https://doi.org/10.1111/clr.14206

Vancouver

Tarce M, Becker K, Lahoud P, Shujaat S, Jacobs R, Quirynen M. Non‐invasive oral implant position assessment: An ex vivo study using a 3D industrial scan as the reference model to mimic the clinical situation. Clinical Oral Implants Research. 2024. doi:10.1111/clr.14206

BibTeX
@article{Tarce2024,
  author = {Tarce, Mihai and Becker, Kathrin and Lahoud, Pierre and Shujaat, Sohaib and Jacobs, Reinhilde and Quirynen, Marc},
  title = {Non‐invasive oral implant position assessment: An ex vivo study using a 3D industrial scan as the reference model to mimic the clinical situation},
  journal = {Clinical Oral Implants Research},
  year = {2024},
  doi = {10.1111/clr.14206}
}
Kostenlos starten →