The Effect of Angulation and Scan Body Position on Scans for Implant‐Treated Edentulism: A Clinical Simulation Study
Der Einfluss von Angulation und Scan-Body-Position auf Scans bei implantatgetragenem zahnlosem Kiefer: eine klinische Simulationsstudie
Clinical Implant Dentistry and Related Research · 2025-04 · 27 (2)
DOI: 10.1111/cid.70001 ↗Auf einen Blick
Die Studie prüfte die Genauigkeit digitaler Abformungen für maxilläre Full-Arch-Implantatprothesen mit 2 Intraoralscannern. Implantatangulation und Scan-Body-Position beeinflussten Trueness und Präzision signifikant.
Fragestellung
Wie beeinflussen Implantatangulation und Scan-Body-Position die Genauigkeit digitaler Abformungen bei maxillär implantatgetragenen Full-Arch-Prothesen?
Methode
Klinische Simulationsstudie mit 2 3D-gedruckten Oberkiefermodellen ohne Zähne und 6 Implantaten; Vergleich von Trios3 und CS3600 in 2 Szenarien, Auswertung linearer und angularer Abweichungen.
Ergebnisse
Implantatangulation hatte einen signifikanten Einfluss auf die Genauigkeit. CS3600 zeigte eine bessere Trueness, Trios3 eine bessere Präzision in beiden Szenarien. Die letzte erfasste Scan-Body-Position wies höhere Abweichungen auf.
Schlussfolgerung der Autor:innen
Beide Scanner erreichten eine akzeptable Genauigkeit. Implantatangulation und Scan-Body-Position beeinflussten Trueness und Präzision signifikant; das Scanprotokoll sollte berücksichtigt werden.
Kernaussagen
- 2 Intraoralscanner wurden in 2 Szenarien verglichen
- Implantatangulation beeinflusste die Genauigkeit signifikant
- Die zuletzt erfasste Scan-Body-Position zeigte höhere Abweichungen
Deutsche Zusammenfassung: KI-gestützt aus dem Original-Abstract erstellt; alle Zahlen wurden automatisch mit dem Original abgeglichen. Maßgeblich ist der Original-Abstract.
Kurz gefasst
Fachartikel in der Zeitschrift Clinical Implant Dentistry and Related Research, online erschienen am 03.03.2025. Verfasst von Georgia Vasileiadi und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, School of Dentistry, Aristotle University of Thessaloniki (AUTh), Thessaloniki, Greece. Hauptthemen laut MEDLINE: Dental Prosthesis, Implant-Supported, Dental Impression Technique, Jaw, Edentulous, Dental Implants. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Introduction
The acquisition of digital impressions has become an integral part of clinical dentistry. The purpose of the present clinical simulation study was to evaluate the accuracy of digital impressions for maxillary full‐arch implant‐supported prostheses using two modern intraoral scanners with different acquisition technologies. Material and Methods Two models of edentulous maxilla, with six implants at positions #16,14,12,22,24,26 (FDI World Dental Federation System, ISO 3950) or #3,5,7,10,12,14 (Universal Numbering system) were digitally designed, and 3D‐printed in resin material (Asiga DentaMODEL, Australia). In the first scenario, all implants were parallelized, while in the second, implants #12/#7 and #22/#10 had a 20° angulation buccally, while implants #16/#3 and #26/#14 20° angulation distally. The models were scanned with two different intraoral scanners, Trios3 (3Shape, Denmark) and CS3600 (Carestream Dental, USA). Linear (x, y, z axes—top point) and angular deviations (x, y, z axes—Δφ) were assessed. Statistical analysis was performed using Kolmogorov–Smirnov tests (significance at p < 0.05).
Results
Implant angulation showed a significant impact on accuracy, while the two scanners showed statistically significant differences. CS3600 demonstrated superior trueness, while Trios3 superior precision in both clinical scenarios. In the first clinical scenario a predominant occurrence of angular deviations was observed, while in the second scenario both angular and linear deviations were recorded. Scan body position also influenced scanning outcomes, with the last scan body captured demonstrating higher deviations.
Conclusion
Both scanners provided acceptable accuracy in the acquisition of digital impressions. Implant angulation and scan body position significantly affected trueness and precision. Clinicians should carefully consider implant angulations in full‐arch implant restorations, as well as the scanning protocol.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Prosthodontics, School of Dentistry, Aristotle University of Thessaloniki (AUTh), Thessaloniki, Greece.
- Department of Mechanical Engineering, School of Engineering, Aristotle University of Thessaloniki (AUTh), Thessaloniki, Greece.
- Laboratory of Biomaterials and Computational Biomechanics, Department of Mechanical Engineering, University of Western Macedonia, Kozani, Greece.
ORCID-Profile: Athina Bakopoulou
Zitieren
APA
Vasileiadi, G., Ximinis, E., Sarafidou, K., Slini, T., Gogomitros, F., Athanasiadis, G. A., Naka, O., Tsouknidas, A., Bakopoulou, A., & Kokoti, M. (2025). The Effect of Angulation and Scan Body Position on Scans for Implant‐Treated Edentulism: A Clinical Simulation Study. Clinical Implant Dentistry and Related Research, 27(2). https://doi.org/10.1111/cid.70001
Vancouver
Vasileiadi G, Ximinis E, Sarafidou K, Slini T, Gogomitros F, Athanasiadis GA, et al. The Effect of Angulation and Scan Body Position on Scans for Implant‐Treated Edentulism: A Clinical Simulation Study. Clinical Implant Dentistry and Related Research. 2025;27(2). doi:10.1111/cid.70001
BibTeX
@article{Vasileiadi2025,
author = {Vasileiadi, Georgia and Ximinis, Evangelos and Sarafidou, Katia and Slini, Theodora and Gogomitros, Fotis and Athanasiadis, George Andreas and Naka, Olga and Tsouknidas, Alexandros and Bakopoulou, Athina and Kokoti, Maria},
title = {The Effect of Angulation and Scan Body Position on Scans for Implant‐Treated Edentulism: A Clinical Simulation Study},
journal = {Clinical Implant Dentistry and Related Research},
year = {2025},
volume = {27},
number = {2},
doi = {10.1111/cid.70001}
}
EUVIMED