EUVIMEDEUVIMED entdecken
Crossref

Biocompatibility and dimensional stability through the use of 3D ‐printed scaffolds made by polycaprolactone and bioglass‐7: An in vitro and in vivo study

Ho-Kyung Lim, In-Seok Song iD, Won-Cheul Choi, Young-Jun Choi, Eun-Young Kim, Thi Hong Tham Phan, Ui-Lyong Lee iD

Clinical Implant Dentistry and Related Research · 2024

DOI: 10.1111/cid.13378 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Clinical Implant Dentistry and Related Research, 2024. Verfasst von Ho-Kyung Lim und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Oral & Maxillofacial Surgery, Korea University Guro Hospital, Seoul, Korea. Hauptthemen laut MEDLINE: Polyesters, Printing, Three-Dimensional, Ceramics, Tissue Scaffolds. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 40 Literaturangaben. Gefördert von: Korea Institute for Advancement of Technology (KIAT).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

This experiment aimed to observe the differences in biological properties by producing BGS‐7 + PCL scaffolds with different weight fractions of BGS‐7 through 3D printing and to confirm whether using the scaffold for vertical bone augmentation is effective. Materials and Methods Cube‐shaped bioglass (BGS‐7) and polycaprolactone (PCL) scaffolds with different weight fractions (PCL alone, PCL with 15% and 30% BGS‐7) are produced using 3D printing. The surface hydroxyapatite (HA) apposition, the pH change, proliferation and attachment assays, and various gene expression levels are assessed. After a 7‐mm implant was inserted 3 mm into the rabbit calvaria, vertical bone augmentation is performed around the implant and inside the scaffold in four ways: scaffold only, scaffold+bone graft, bone graft only, and no graft. Sacrifice is performed at 6, 12, and 24 weeks, and the various parameters are compared radiographically and histologically.

Results

HA apposition, cell proliferation, cell attachment, and expression of osteogenic genes increase as the proportion of BGS‐7 increase. In the in vivo test, a higher bone–implant contact ratio, bone volume ratio, bone mineral density, and new bone area are observed when the scaffold and bone grafts were used together.

Conclusion

The 3D‐printed scaffold, a mixture of BGS‐7 and PCL, exhibit higher biological compatibility as the proportion of BGS‐7 increase. Additionally, the use of scaffold is effective for vertical bone augmentation.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

PolyestersPrinting, Three-DimensionalCeramicsTissue ScaffoldsBiocompatible MaterialsRabbitsAnimalsMaterials TestingCell ProliferationDurapatite

Stichwörter der Autor:innen

3D printingalveolar ridge augmentationbioglass‐7polycaprolactone

Substanzen

PolyesterspolycaprolactoneBioglassBiocompatible MaterialsDurapatite

Autor:innen und Institutionen

  • Department of Oral & Maxillofacial Surgery, Korea University Guro Hospital, Seoul, Korea.
  • Department of Oral & Maxillofacial Surgery, Korea University Anam Hospital, Seoul, Korea.
  • Department of Orthodontics, Dental Center, Chung-Ang University Hospital, Seoul, Korea.
  • Department of Oral & Maxillofacial Surgery, Chung-Ang University College of Medicine, Seoul, Korea.

ORCID-Profile: In-Seok Song, Ui-Lyong Lee

Förderung

  • Korea Institute for Advancement of Technology (KIAT)

Zitieren

APA

Lim, H. K., Song, I. S., Choi, W. C., Choi, Y. J., Kim, E. Y., Phan, T. H. T., & Lee, U. L. (2024). Biocompatibility and dimensional stability through the use of 3D ‐printed scaffolds made by polycaprolactone and bioglass‐7: An in vitro and in vivo study. Clinical Implant Dentistry and Related Research. https://doi.org/10.1111/cid.13378

Vancouver

Lim HK, Song IS, Choi WC, Choi YJ, Kim EY, Phan THT, et al. Biocompatibility and dimensional stability through the use of 3D ‐printed scaffolds made by polycaprolactone and bioglass‐7: An in vitro and in vivo study. Clinical Implant Dentistry and Related Research. 2024. doi:10.1111/cid.13378

BibTeX
@article{Lim2024,
  author = {Lim, Ho-Kyung and Song, In-Seok and Choi, Won-Cheul and Choi, Young-Jun and Kim, Eun-Young and Phan, Thi Hong Tham and Lee, Ui-Lyong},
  title = {Biocompatibility and dimensional stability through the use of 3D ‐printed scaffolds made by polycaprolactone and bioglass‐7: An in vitro and in vivo study},
  journal = {Clinical Implant Dentistry and Related Research},
  year = {2024},
  doi = {10.1111/cid.13378}
}
Kostenlos starten →