Enhancing Performance of Fluxgate Sensors Using Annealed Nanocrystalline Core
IEEE Transactions on Magnetics · 2023-09 · 59 (9) · 1-9
DOI: 10.1109/tmag.2023.3296205 ↗Kurz gefasst
Fachartikel in der Zeitschrift IEEE Transactions on Magnetics, 2023-09. Verfasst von Diana Hrakova und 2 weiteren Autor:innen. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 24 Literaturangaben. Gefördert von: Student Grant Competition of Czech Technical University in Prague within the Soft Magnetic Particles Project.
Abstract (Originalsprache)
The magnetic core is one of the most important parts of a fluxgate sensor. This article presents a study of fluxgate sensors with a core based on nanocrystalline Fe73.5Cu1Nb3Si13.5B9 wire and compares their performance to that of sensors based on amorphous wire with a chemical composition of (Co94Fe6)75Si15B10. Both wires have a diameter of 0.12 mm and were manufactured by the Institute of Technical Physics, Iasi, Romania. The nanocrystalline as-cast (AC) FINEMET wire was annealed by the flash current method to heat up the wire to the temperature of crystallization from −590 °C to 605 °C in a few seconds, using Joule heat from 495 to 505 mA of applied current. The annealing process was carried out in a tube filled with Ar gas to prevent the surface oxidation of the annealed wire. Stress tension of 8–170 MPa was applied during the annealing. The annealing process was carried out under different conditions such as annealing duration, applied current, and applied stress to find the optimum parameters for the performance of the fluxgate sensor. The material and sensor characterization was complemented by the Mössbauer spectroscopy. The annealing results in changes in the microstructure of the AC amorphous alloy, and annealing parameters influence the amorphous-to-nanocrystalline ratio and the size of nanocrystalline grains. These controllable parameters are the keys to the improvements of the material and using the advantages of both states. The characteristics of the fluxgate sensor with the FINEMET core annealed under certain conditions—tensile stress 12 MPa, annealing current 497 mA, and duration 15 s—are comparable to the traditionally-used Cobalt (Co)-based amorphous core in terms of sensitivity and magnetic noise, around 0.8–0.9 V/mT and 20–26 pT/ $\surd $ Hz, respectively, at 8 kHz. The advantage of nanocrystalline material is that it can work at elevated temperatures as its Curie point is higher than the Curie point and crystallization temperature of Co-based amorphous alloys.
Förderung
- Student Grant Competition of Czech Technical University in Prague within the Soft Magnetic Particles Project
Zitieren
APA
Hrakova, D., Ripka, P., & Kmječ, T. (2023). Enhancing Performance of Fluxgate Sensors Using Annealed Nanocrystalline Core. IEEE Transactions on Magnetics, 59(9), 1-9. https://doi.org/10.1109/tmag.2023.3296205
Vancouver
Hrakova D, Ripka P, Kmječ T. Enhancing Performance of Fluxgate Sensors Using Annealed Nanocrystalline Core. IEEE Transactions on Magnetics. 2023;59(9):1-9. doi:10.1109/tmag.2023.3296205
BibTeX
@article{Hrakova2023,
author = {Hrakova, Diana and Ripka, Pavel and Kmječ, Tomáš},
title = {Enhancing Performance of Fluxgate Sensors Using Annealed Nanocrystalline Core},
journal = {IEEE Transactions on Magnetics},
year = {2023},
volume = {59},
number = {9},
pages = {1--9},
doi = {10.1109/tmag.2023.3296205}
}
EUVIMED