Airborne Capacitive Micromachined Ultrasonic Transducers in Pitch–Catch Mode: Modeling and Characterization of the Measurement Chain
IEEE Open Journal of Ultrasonics, Ferroelectrics, and Frequency Control · 2026 · 6 · 94-106
DOI: 10.1109/ojuffc.2026.3680024 ↗Kurz gefasst
Fachartikel in der Zeitschrift IEEE Open Journal of Ultrasonics, Ferroelectrics, and Frequency Control, 2026. Verfasst von Yilihamu Abudujiasuer und 4 weiteren Autor:innen. Die Arbeit nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: French National Research Agency (ANR) under the Mesure des propriétés physIques des Gaz à l'aide de MEMS résoNnants pour la détectiON chimique en milieu hostil…, Centre d'Études et de Recherches Technologiques en Microélectronique (CERTeM) Technological Platform.
Abstract (Originalsprache)
Capacitive Micromachined Ultrasonic Transducers (CMUTs) feature broadband operation as well as high sensitivity, showing promise for applications such as pressure sensing, ultrasonic imaging, and wireless power transfer. Although widely used in medical and underwater settings, CMUTs are also well-suited to air-coupled operation. As an illustrative example, CMUT-based gas detection can be achieved by monitoring ultrasonic properties of the medium (acoustic velocity and attenuation). This paper focuses on a modeling approach for a complete CMUT-based airborne pitch-catch measurement, across a wide frequency range from 0.5 MHz to 5 MHz. A lumped-element equivalent circuit of the CMUT array is used for transducer modeling, with parameters extracted experimentally from electrical impedance measurements and interferometric displacement analysis. Acoustic pressure propagation in air is simulated using Field II in MATLAB, incorporating frequency-dependent air attenuation ( $\approx ~100$ Np/m at 2.5 MHz) obtained from dedicated experiments. The performance of three preamplifier types (voltage, charge, and transimpedance) is evaluated at a 6 mm separation distance between the transmitter and receiver. For a 2.5 MHz-centered excitation signal with an amplitude of 10 V and biased at 45 V, the measured and simulated output amplitudes reach approximately 30 dBmV with a voltage amplifier, 35 dBmV with a transimpedance amplifier, and 40 dBmV with a charge amplifier. The simulations agree well with the experimental results, confirming reliable and predictable ultrasonic sensing in air using CMUTs and paving the way for future work, such as gas-sensing modeling.
Förderung
- French National Research Agency (ANR) under the Mesure des propriétés physIques des Gaz à l'aide de MEMS résoNnants pour la détectiON chimique en milieu hostil…
- Centre d'Études et de Recherches Technologiques en Microélectronique (CERTeM) Technological Platform
Zitieren
APA
Abudujiasuer, Y., Lemaire, E., Barcella, F., Dufour, I., & Certon, D. (2026). Airborne Capacitive Micromachined Ultrasonic Transducers in Pitch–Catch Mode: Modeling and Characterization of the Measurement Chain. IEEE Open Journal of Ultrasonics, Ferroelectrics, and Frequency Control, 6, 94-106. https://doi.org/10.1109/ojuffc.2026.3680024
Vancouver
Abudujiasuer Y, Lemaire E, Barcella F, Dufour I, Certon D. Airborne Capacitive Micromachined Ultrasonic Transducers in Pitch–Catch Mode: Modeling and Characterization of the Measurement Chain. IEEE Open Journal of Ultrasonics, Ferroelectrics, and Frequency Control. 2026;6:94-106. doi:10.1109/ojuffc.2026.3680024
BibTeX
@article{Abudujiasuer2026,
author = {Abudujiasuer, Yilihamu and Lemaire, Etienne and Barcella, Flavien and Dufour, Isabelle and Certon, Dominique},
title = {Airborne Capacitive Micromachined Ultrasonic Transducers in Pitch–Catch Mode: Modeling and Characterization of the Measurement Chain},
journal = {IEEE Open Journal of Ultrasonics, Ferroelectrics, and Frequency Control},
year = {2026},
volume = {6},
pages = {94--106},
doi = {10.1109/ojuffc.2026.3680024}
}
EUVIMED