GaN/Si SAW-Based Temperature and Humidity Sensors Operable on Curved Surfaces
IEEE Sensors Journal · 15.06.2026 · 26 (12) · 19262-19274
DOI: 10.1109/jsen.2026.3690871 ↗Kurz gefasst
Fachartikel in der Zeitschrift IEEE Sensors Journal, erschienen am 15.06.2026. Verfasst von Dan Vasilache und 13 weiteren Autor:innen. Die Arbeit nennt 50 Literaturangaben.
Abstract (Originalsprache)
This article presents GHz surface acoustic wave (SAW) temperature and humidity sensors, manufactured on GaN/Si, bonded on curved surfaces. The technological process includes advanced nano-lithographical techniques for the fabrication of the interdigitated transducers (IDTs), having digits width of 167 nm. The humidity sensors have a SiO2 functionalization layer deposited over the IDTs. The silicon substrate is thinned down to $\sim 60 \mu{\mathrm {m}}$ as the final process before dicing the devices. This thickness ensures the flexibility of the chip and, at the same time, a safe handling. The chips are bonded on convex and concave surfaces manufactured from aluminum cylindrical tubes, having radii of 28, 36, and 44 mm. The on-wafer measurements of the bonded SAW structures (for both Rayleigh and Sezawa propagation modes) show: 1) an increase of the resonance frequency for convex surface and 2) a decrease for concave surface, when compared to the measurements of the initial chips, before bonding. These experimental results are confirmed by COMSOL simulations. This article further explores the functionality of temperature and humidity SAW sensors mounted on both convex and concave surfaces, by comparing the sensitivities with the values obtained for similar SAW structures mounted on flat surfaces. Very good temperature sensitivities are determined for both propagation modes (~170 kHz/K). The measurements demonstrate that the temperature sensitivities remain unchanged irrespective of the type of surface curvature. The humidity sensitivity versus relative humidity (RH) measurements performed in the range 30%RH–80%RH show a nonlinear behavior for the SAW humidity sensors bonded on curved surfaces. A significant increase of the humidity sensitivity (compared to the structures bonded on flat surface), especially for RH, above 50%, was obtained, reaching values that exceed 100 kHz/%RH. This behavior is qualitatively explained through the atomic force microscope (AFM)-based roughness analysis of SiO2 functionalization layers after bonding of SAW sensors on flat and curved surfaces.
Zitieren
APA
Vasilache, D., Boldeiu, G., Nastase, C., Nedelcu, M., Aslanidis, E., Nicoloiu, A., Zdru, I., Pasteanu, M., Parvulescu, C., Dinescu, A., Gavrilă, R., Konstantinidis, G., Ziaei, A., & Müller, A. (2026). GaN/Si SAW-Based Temperature and Humidity Sensors Operable on Curved Surfaces. IEEE Sensors Journal, 26(12), 19262-19274. https://doi.org/10.1109/jsen.2026.3690871
Vancouver
Vasilache D, Boldeiu G, Nastase C, Nedelcu M, Aslanidis E, Nicoloiu A, et al. GaN/Si SAW-Based Temperature and Humidity Sensors Operable on Curved Surfaces. IEEE Sensors Journal. 2026;26(12):19262-19274. doi:10.1109/jsen.2026.3690871
BibTeX
@article{Vasilache2026,
author = {Vasilache, Dan and Boldeiu, George and Nastase, Claudia and Nedelcu, Monica and Aslanidis, Evangelos and Nicoloiu, Alexandra and Zdru, Ioana and Pasteanu, Mircea and Parvulescu, Catalin and Dinescu, Adrian and Gavrilă, Raluca and Konstantinidis, George and Ziaei, Afshin and Müller, Alexandru},
title = {GaN/Si SAW-Based Temperature and Humidity Sensors Operable on Curved Surfaces},
journal = {IEEE Sensors Journal},
year = {2026},
volume = {26},
number = {12},
pages = {19262--19274},
doi = {10.1109/jsen.2026.3690871}
}
EUVIMED