EUVIMEDEUVIMED entdecken
Crossref

Hydrothermally Synthesized pH-Tailored Ag-Doped ZnO Nanostructure for Printed Room-Temperature NO₂ Gas Sensor

Nikhila Patil, Neethu Thomas, Anupama Behera, Parasuraman Swaminathan, P. Sumathi

IEEE Sensors Journal · 15.02.2026 · 26 (4) · 5275-5287

DOI: 10.1109/jsen.2025.3648412 ↗

Kurz gefasst

Fachartikel in der Zeitschrift IEEE Sensors Journal, erschienen am 15.02.2026. Verfasst von Nikhila Patil und 4 weiteren Autor:innen. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 54 Literaturangaben. Gefördert von: Indian Nanoelectronics Users’ Program—Idea to Innovation, Ministry of Electronics and Information Technology (MeitY) and the Electronic Materials and Thin Film Laboratory (EMFTL) Laboratory at Indian Institute of Tech….

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

pH-tailored Ag-doped ZnO (AgZO) nanostructures with controlled morphologies are developed through a cost-effective hydrothermal technique. The nanostructure morphology evolves from flower-like structures at pH 7 (average petal length: 1.7 ± 0.65 μm), to star-like rods at pH 10 (length: 0.97 ± 0.33 μm), and finally to needle-like self-assemblies at pH 12 (length: 4.4 ± 1.92 μm). Optical, chemical, and morphological investigations confirmed the presence of wurtzite ZnO, Ag incorporation, increased oxygen vacancies, and tunable bandgap from 3.51 eV (pH 7) to 3.09 eV (pH 12). Surface area analysis demonstrates a surface area variation from 37.18 m2/g at pH 7 to 5.15 m2/g at pH 12. Printable AgZO ink was formulated and printed on Ag-interdigitated electrodes to fabricate a miniature room temperature printed NO2 gas sensor. Among all devices, the pH 12 sensor exhibited improved performance, attributed to its anisotropic morphology, enhanced crystallinity, and optimized defect-assisted charge transport. The pH 12 sensor demonstrated a stable response (R) of 16.2% at 32 PPM, with a response and recovery time of 107 and 130 s, consistent multicycle operation, and strong concentration-dependent resistance modulation from 16–40 PPM. Selectivity toward NO2 was confirmed through negligible interference from CO2. These results demonstrate that pH-controlled Ag incorporation significantly influences surface reactivity and electrondepletion dynamics, enabling efficient printed NO2 sensor operating at room temperature. The approach provides a low-cost, scalable route for fabricating high-performing gas-sensing materials.

Förderung

  • Indian Nanoelectronics Users’ Program—Idea to Innovation
  • Ministry of Electronics and Information Technology (MeitY) and the Electronic Materials and Thin Film Laboratory (EMFTL) Laboratory at Indian Institute of Tech…

Zitieren

APA

Patil, N., Thomas, N., Behera, A., Swaminathan, P., & Sumathi, P. (2026). Hydrothermally Synthesized pH-Tailored Ag-Doped ZnO Nanostructure for Printed Room-Temperature NO₂ Gas Sensor. IEEE Sensors Journal, 26(4), 5275-5287. https://doi.org/10.1109/jsen.2025.3648412

Vancouver

Patil N, Thomas N, Behera A, Swaminathan P, Sumathi P. Hydrothermally Synthesized pH-Tailored Ag-Doped ZnO Nanostructure for Printed Room-Temperature NO₂ Gas Sensor. IEEE Sensors Journal. 2026;26(4):5275-5287. doi:10.1109/jsen.2025.3648412

BibTeX
@article{Patil2026,
  author = {Patil, Nikhila and Thomas, Neethu and Behera, Anupama and Swaminathan, Parasuraman and Sumathi, P.},
  title = {Hydrothermally Synthesized pH-Tailored Ag-Doped ZnO Nanostructure for Printed Room-Temperature NO₂ Gas Sensor},
  journal = {IEEE Sensors Journal},
  year = {2026},
  volume = {26},
  number = {4},
  pages = {5275--5287},
  doi = {10.1109/jsen.2025.3648412}
}
Kostenlos starten →