EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A Microcontroller-Based System for Tool Condition Monitoring: Assessing the Viability of Low-Cost Vibration and Current Sensors

Gustavo Rogerio Da Silva Barbosa, Leandro Pontes De Andrade, Ricardo Ataide De Lima, Joao Fausto Lorenzato De Oliveira, Rogerio Pontes De Araujo

IEEE Access · 2026 · 14 · 117106-117123

DOI: 10.1109/access.2026.3718875 ↗

Kurz gefasst

Fachartikel in der Zeitschrift IEEE Access, 2026. Verfasst von Gustavo Rogerio Da Silva Barbosa und 4 weiteren Autor:innen. Die Arbeit nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Brasil (CAPES) - Finance Code 001.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Tool condition monitoring (TCM) is essential for maintaining machining efficiency and workpiece quality. However, the prohibitive cost of industrial-grade instrumentation remains a barrier for small-to-medium enterprises. In this context, we evaluated a low-cost (approximately US ${\$}$ 30) multisensor architecture for in-process flank wear monitoring, assessing the individual diagnostic capabilities of vibration and electrical current sensing. The system integrates an MPU-9250 microelectromechanical systems (MEMS) accelerometer and an SCT013-000 current sensor with an ESP32 microcontroller, operating at a 2 kHz sampling rate via a wired UART serial interface. Vibration RMS exhibited a strong positive correlation with flank wear ( $\rho =0.94$ ), while frequency-domain analysis revealed statistically significant spectral centroid migration and harmonic power shifts consistent with tool degradation. Conversely, electrical current sensing yielded a negligible correlation ( $\rho = -0.09$ ), indicating that wear-induced load variations were overshadowed by the spindle’s baseline power demand under the tested cutting conditions. These findings suggest that the viability of low-cost current sensing depends on the machining regime, particularly the relative contribution of cutting power to total spindle load. Benchmarking confirmed that the proposed system achieves the highest sampling rate among reviewed MEMS-based academic prototypes while operating at approximately 15% of the cost of the closest comparable setup. Although the limited experimental dataset (n = 6) warrants further validation, these results indicate that vibration-based MEMS sensing is a promising low-cost modality for TCM in finishing operations, and that the diagnostic sensitivity of current sensing is contingent on the operating conditions.

Förderung

  • Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Brasil (CAPES) - Finance Code 001

Zitieren

APA

Barbosa, G. R. D. S., Andrade, L. P. D., Lima, R. A. D., Oliveira, J. F. L. D., & Araujo, R. P. D. (2026). A Microcontroller-Based System for Tool Condition Monitoring: Assessing the Viability of Low-Cost Vibration and Current Sensors. IEEE Access, 14, 117106-117123. https://doi.org/10.1109/access.2026.3718875

Vancouver

Barbosa GRDS, Andrade LPD, Lima RAD, Oliveira JFLD, Araujo RPD. A Microcontroller-Based System for Tool Condition Monitoring: Assessing the Viability of Low-Cost Vibration and Current Sensors. IEEE Access. 2026;14:117106-117123. doi:10.1109/access.2026.3718875

BibTeX
@article{Barbosa2026,
  author = {Barbosa, Gustavo Rogerio Da Silva and Andrade, Leandro Pontes De and Lima, Ricardo Ataide De and Oliveira, Joao Fausto Lorenzato De and Araujo, Rogerio Pontes De},
  title = {A Microcontroller-Based System for Tool Condition Monitoring: Assessing the Viability of Low-Cost Vibration and Current Sensors},
  journal = {IEEE Access},
  year = {2026},
  volume = {14},
  pages = {117106--117123},
  doi = {10.1109/access.2026.3718875}
}
Kostenlos starten →