EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A 3D Printed Human Ear Model for Standardized Testing of Hearing Protection Devices to Blast Exposure

Marcus A Brown, Shangyuan Jiang, Rong Z Gan

Otology & Neurotology Open · 2022

DOI: 10.1097/ono.0000000000000010 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Otology & Neurotology Open, 2022. Verfasst von Marcus A Brown und 2 weiteren Autor:innen. Beteiligte Einrichtung: Stephenson School of Biomedical Engineering, University of Oklahoma, Norman, OK. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 22 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Hypothesis: A 3D printed human temporal bone (TB) that is anatomically accurate would cost-effectively reproduce the responses observed in blast testing of human cadaveric TBs with and without passive hearing protection devices (HPDs).

Background

HPDs have become critical personal protection equipment against auditory damage for service members. Acoustic test fixtures and human TBs have been used to test and develop HPDs; however, the lack of a cost-effective, standardized model impedes the improvement of HPDs.

Methods

In this study, the 3D printed TB model was printed with flexible and rigid polymers and consisted of the ear canal, tympanic membrane (TM), ossicular chain, middle ear suspensory ligaments/muscle tendons, and middle ear cavity. The TM movement under acoustic stimulation was measured with laser Doppler vibrometry. The TB model was then exposed to blasts with or without HPDs and pressures at the ear canal entrance (P0) and near the TM in the ear canal (P1) were recorded. All results were compared with that measured in human TBs.

Results

Results indicated that in the 3D printed TB, the attenuated peak pressures at P1 induced by HPDs ranged from 0.92 to 1.06 psi (170–171 dB) with blast peak pressures of 5.62–6.54 psi (186–187 dB) at P0, and measured results were within the mean and SD of published data. Vibrometry measurements also followed a similar trend as the published results.

Conclusions

The 3D printed TB model accurately evaluated passive HPDs’ protective function during blast and the potential for use as a model for acoustic transmission was investigated.

Schlagwörter

Stichwörter der Autor:innen

3D printingBlast overpressureEarHearing protection devicesHuman temporal bone

Autor:innen und Institutionen

  • Stephenson School of Biomedical Engineering, University of Oklahoma, Norman, OK.
  • School of Aerospace and Mechanical Engineering, University of Oklahoma, Norman, OK.

Zitieren

APA

Brown, M. A., Jiang, S., & Gan, R. Z. (2022). A 3D Printed Human Ear Model for Standardized Testing of Hearing Protection Devices to Blast Exposure. Otology & Neurotology Open. https://doi.org/10.1097/ono.0000000000000010

Vancouver

Brown MA, Jiang S, Gan RZ. A 3D Printed Human Ear Model for Standardized Testing of Hearing Protection Devices to Blast Exposure. Otology & Neurotology Open. 2022. doi:10.1097/ono.0000000000000010

BibTeX
@article{Brown2022,
  author = {Brown, Marcus A and Jiang, Shangyuan and Gan, Rong Z},
  title = {A 3D Printed Human Ear Model for Standardized Testing of Hearing Protection Devices to Blast Exposure},
  journal = {Otology & Neurotology Open},
  year = {2022},
  doi = {10.1097/ono.0000000000000010}
}
Kostenlos starten →