EUVIMEDEUVIMED entdecken
Crossref

Simultaneous Energy-Filtered 4D-STEM and Quantitative XEDS Analysis for Strain and Composition Mapping in Semiconductor Materials

Alexander Campos-Quiros, Kotaro Sakaguchi, Takeshi Kaneko, Masashi Watanabe

Microscopy and Microanalysis · 27.07.2026 · 32 (Supplement_1)

DOI: 10.1093/mam/ozag053.016 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Microscopy and Microanalysis, online erschienen am 27.07.2026. Verfasst von Alexander Campos-Quiros und 3 weiteren Autor:innen. Die Arbeit nennt 9 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Accurate control of composition and lattice strain is a critical aspect of modern semiconductor devices. In heteroepitaxial strained systems, such as Si/Si(1-x)Gex multilayer materials, composition and strain determine the electronic and optoelectronic properties of the material [1]. However, variation in the layer thickness and the formation of interfacial misfit dislocations can induce strain relaxation for a given composition [2]. It is very important to characterize both composition and strain simultaneously for understanding their direct correlations. Conventional characterization approaches, such as electron energy-loss spectrometry (EELS) for chemical composition analysis, can hardly be performed simultaneously with diffraction experiments by four-dimensional scanning transmission electron microscopy (4D-STEM). The sequential EELS and 4D-STEM analysis approach can lead to spatial drift and specimen beam damage, limiting a pixel-by-pixel correlative analysis. This is of great interest, as the strain and composition variations typically occur at the nano- and sub-nanometer scale in semiconductor devices. To address this limitation and enable a higher-throughput methodology, simultaneous X-ray energy dispersive spectrometry (XEDS) and energy-filtered 4D-STEM analyses were carried out to determine the composition and thickness, as well as the lattice strain in a Si/Si(1-x)Gex multilayer. A commercial Si/Si0.81Ge0.19 multilayer specimen (MAG*I*CALTM) [3] was utilized in this study. The Si0.81Ge0.19 multilayer stack was epitaxially grown on a single crystal Si substrate, giving rise to strained layers. Simultaneous XEDS and energy-filtered 4D-STEM analysis was performed in an aberration-corrected STEM JEOL JEM-ARM200CF operated at 200 kV. For the 4D-STEM analysis, the nanobeam diffraction mode was established by tuning the microscope alignment parameters, condenser lens strengths (CL1, CL3, and CM), and the aberration corrector. A convergence semiangle of ∼2.8 mrad and a camera length of 3 cm were employed for the 4D-STEM analysis in this study. To minimize the effect of inelastic scattering, including thermal diffuse scattering on the diffraction patterns, zero-loss filtering was applied using a CEOS Energy-Filtering and Imaging Device (CEFID) with an energy window of 10 eV. Zero-loss filtered 4D-STEM datasets were recorded using a Dectris ELA hybrid-pixelated detector mounted after the CEFID system. Non-isochromaticity, geometrical distortions, and chromatic distortions were minimized using CEOS Panta Rhei software prior to the 4D-STEM acquisition. Simultaneous XEDS and 4D-STEM acquisition, controlled by JEOL FEMTUS software, was carried out using a dwell time of 100 ms and a probe current of ∼155 pA. Strain analysis was performed using the py4dstem Python package [4], while the composition and thickness determination were performed using the ζ-factor method [5,6]. Figure 1 summarizes the quantitative XEDS analysis. The high-angle annular dark-field (HAADF) STEM image (Figure 2(a)) shows an enhanced intensity at the location of the SiGe layers, consistent with the higher atomic number of Ge compared to Si. Quantitative composition maps obtained from the Ge-K and Si-K peaks are presented in Figure 1(b-c). Moreover, the specimen thickness map determined by the ζ-factor method is shown in Figure 1(d). For easier interpretation of the XEDS quantitative analysis, composition and thickness profiles across the Si/SiGe multilayer stack are presented in Figure 1(e). The measured Ge concentration was in excellent agreement with the nominal 19 at% of Ge, as indicated by red dashed lines. The quantified composition results were then directly correlated with the lattice strain mapped by 4D-STEM (Figure 2). Figure 2(a) shows an HAADF-STEM image obtained simultaneously with the 4D-STEM dataset. A reference region (red box in Figure 2(a)) corresponding to the Si substrate was used for the strain mapping. Strain maps corresponding to ɛxx, ɛyy, and ɛxy (Figure 2(b-d)) were extracted using g vectors indicated in the representative diffraction pattern in Figure 2 (e). The layers corresponding to SiGe exhibit a tensile strain in the ɛxx strain map with respect to the Si substrate, while the ɛyy presents a minimal strain. To validate the strain measurements, Vegard’s law was employed to estimate the strain possibly caused by the lattice expansion at the Si0.81Ge0.19 layers with respect to Si. Based on the local fluctuations of the atomic percent of Ge (xGe) quantified by XEDS analysis, the strain component in the x-direction can be estimated as ɛxx≈((aGe/aSi)-1)xGe(1+2ν) [7]. Here, aGe and aSi are the Ge and Si lattice constants (0.56575 nm and 0.54310 nm, respectively [8]), and ν is the Poisson’s ratio of Si and Ge in the direction of 0.275 [7]. The comparison between measured and estimated strain exhibits strong agreement, as shown in Figure 2(f). Additionally, Figure 2(g) shows the ɛyy strain profile, confirming the minimal lattice distortion in the y-direction, as expected in an epitaxial growth. These results demonstrate that simultaneous XEDS analysis and energy-filtered 4D-STEM, and subsequent quantification, provide a robust characterization strategy for composition and strain mapping of semiconductor devices. Future exploration of this approach will focus on expanding the capabilities to analyze diverse materials from ceramic to metal alloys [9]. Quantitative XEDS analysis of the Si/Si0.81Ge0.19 multilayer specimen using the ζ-factor method. (a) HAADF-STEM image and elemental maps corresponding to (b) Ge and (c) Si compositions, as well as (d) specimen thickness. (e) Concentration and thickness profiles extracted from the regions indicated by dashed boxes in (c-d). Error bars in (e) represent a 99% confidence level (3σ). The black dashed lines in the lookup table in (b-c) correspond to the nominal Ge composition of 19 at%. Energy-filtered 4D-STEM strain analysis of the Si/Si0.81Ge0.19 multilayer specimen. (a) HAADF-STEM image and strain maps corresponding to components (b) ɛxx, (c) ɛyy, and (d) ɛxy. (e) Representative diffraction pattern indicated the g-vectors (g1 and g2) utilized for the strain mapping analysis. Strain profiles corresponding to (f) ɛxx and (g) ɛyy components.

Zitieren

APA

Campos-Quiros, A., Sakaguchi, K., Kaneko, T., & Watanabe, M. (2026). Simultaneous Energy-Filtered 4D-STEM and Quantitative XEDS Analysis for Strain and Composition Mapping in Semiconductor Materials. Microscopy and Microanalysis, 32(Supplement_1). https://doi.org/10.1093/mam/ozag053.016

Vancouver

Campos-Quiros A, Sakaguchi K, Kaneko T, Watanabe M. Simultaneous Energy-Filtered 4D-STEM and Quantitative XEDS Analysis for Strain and Composition Mapping in Semiconductor Materials. Microscopy and Microanalysis. 2026;32(Supplement_1). doi:10.1093/mam/ozag053.016

BibTeX
@article{CamposQuiros2026,
  author = {Campos-Quiros, Alexander and Sakaguchi, Kotaro and Kaneko, Takeshi and Watanabe, Masashi},
  title = {Simultaneous Energy-Filtered 4D-STEM and Quantitative XEDS Analysis for Strain and Composition Mapping in Semiconductor Materials},
  journal = {Microscopy and Microanalysis},
  year = {2026},
  volume = {32},
  number = {Supplement_1},
  doi = {10.1093/mam/ozag053.016}
}
Kostenlos starten →