Digital analyses of Bolton tooth size ratios and their association to gender, angle class, and other occlusal traits: a study using a partially automated digital 3D model analysis
European Journal of Orthodontics · 2024
DOI: 10.1093/ejo/cjae046 ↗Kurz gefasst
Fachartikel in der Zeitschrift European Journal of Orthodontics, 2024. Verfasst von Julia Vorloeper und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthodontics, RWTH Aachen University, 52074, Aachen, Germany. Hauptthemen laut MEDLINE: Odontometry, Malocclusion, Imaging, Three-Dimensional, Tooth. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 50 Literaturangaben.
Abstract (Originalsprache)
Background
This study aims to verify Bolton’s values for tooth size ratios and to evaluate possible relationships to different occlusal traits using precise digital measurement methods. Materials and methods Including 1000 consecutively selected patients from three study centres a digital, partially automated model analysis was performed utilizing the software OnyxCeph. The measurements comprised tooth width for calculation of anterior (AR) and overall ratio (OR) as a percentage, arch width, length, perimeter, overjet, overbite, space analysis in millimetre and the assessment of the angle classification.
Results
AR and OR were significantly increased compared to Bolton’s ratios of 77.2% (AR) and 91.3% (OR). In the gender comparison, male patients showed larger tooth size ratios, especially in the OR. Patients with Angle Class II/1 and II/2 had smaller tooth size ratios than patients with Angle Class III and I. Thus, patients with Angle Class II/1 had the largest tooth diameters in all maxillary teeth and with Angle Class II/2 the smallest tooth sizes in the mandible. The largest tooth widths in the lower jaw were observed in the Angle Class III patient group. Furthermore, a negative correlation from AR/OR to overjet, overbite, and available space in lower jaw as well as a positive correlation to available space in upper jaw was detected.
Conclusions
There is a clear correlation between the tooth size ratios and the present dysgnathia as well as other orthodontically relevant occlusal traits. This prior knowledge about our patients is extremely important to create an individualized treatment plan and enable sufficient occlusion. To achieve a functionally good occlusion with correct overjet and overbite, it is essential that the maxillary and mandibular teeth are proportional in size. Any deviation from the ideal patient in terms of tooth size, number, shape, or arch must be considered in the pre-therapeutic treatment plan in combination with the existing dysgnathia in order to be able to achieve a stable anterior and posterior occlusion with appropriate adjustments to the therapy post-therapeutically.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Orthodontics, RWTH Aachen University, 52074, Aachen, Germany.
ORCID-Profile: Rogerio B Craveiro, Michael Wolf
Zitieren
APA
Vorloeper, J., Coenen, F. A., Lang, N. A., Niederau, C., Knaup, I., Craveiro, R. B., & Wolf, M. (2024). Digital analyses of Bolton tooth size ratios and their association to gender, angle class, and other occlusal traits: a study using a partially automated digital 3D model analysis. European Journal of Orthodontics. https://doi.org/10.1093/ejo/cjae046
Vancouver
Vorloeper J, Coenen FA, Lang NA, Niederau C, Knaup I, Craveiro RB, et al. Digital analyses of Bolton tooth size ratios and their association to gender, angle class, and other occlusal traits: a study using a partially automated digital 3D model analysis. European Journal of Orthodontics. 2024. doi:10.1093/ejo/cjae046
BibTeX
@article{Vorloeper2024,
author = {Vorloeper, Julia and Coenen, Franziska A and Lang, Norbert A and Niederau, Christian and Knaup, Isabel and Craveiro, Rogerio B and Wolf, Michael},
title = {Digital analyses of Bolton tooth size ratios and their association to gender, angle class, and other occlusal traits: a study using a partially automated digital 3D model analysis},
journal = {European Journal of Orthodontics},
year = {2024},
doi = {10.1093/ejo/cjae046}
}
EUVIMED