EUVIMEDEUVIMED entdecken
Randomisierte kontrollierte StudieOpen Access · CC BY-NC-ND 4.0

Stability, survival, patient satisfaction, and cost-minimization of CAD/CAM versus conventional multistranded fixed retainers in orthodontic patients: a 2-year follow-up of a two-centre randomized controlled trial

Helen Pullisaar, Paolo M Cattaneo iD, Arwa Gera iD, Monika Sankiewicz, Małgorzata Bilińska, Vaska Vandevska-Radunovic, Marie A Cornelis iD

European Journal of Orthodontics · 2024

DOI: 10.1093/ejo/cjae006 ↗

Kurz gefasst

Randomisierte kontrollierte Studie in der Zeitschrift European Journal of Orthodontics, 2024. Verfasst von Helen Pullisaar und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthodontics, Institute of Clinical Dentistry, Faculty of Dentistry, University of Oslo, Geitmyrsveien 69/71, Oslo 0455, Norway. Hauptthemen laut MEDLINE: Patient Satisfaction, Orthodontic Retainers. Die Arbeit wurde bisher 23-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Aarhus University Forskingsfond, European Orthodontic Society Research Grant.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

CAD/CAM (computer-aided design/computer-aided manufacturing) fixed retainers (FRs) as an alternative to multistranded FRs to maintain orthodontic treatment outcome.

Objectives

The primary aim was to compare CAD/CAM versus conventional multistranded FRs in terms of stability until 2 years. Secondary outcomes were failure rates, patient satisfaction, and cost-minimization. Trial design 2-arm parallel, two-centre randomized controlled trial.

Methods

Patients were randomized to CAD/CAM or conventional FRs in both arches, in a 1:1 ratio and blocks of four. Allocation concealment was secured by using sequentially numbered envelopes. Patients were blinded. FRs were bonded at the end of treatment, and patients were recalled after 12 and 24 months. First-time retainer failures were recorded and digital impressions were taken. Arch widths and lengths, as well as Little’s Irregularity Index (LII), were measured. Additionally, patients answered satisfaction questionnaires. Linear mixed models were applied for measurements and patient satisfaction. Survival analyses were estimated with Kaplan–Meier curves, along with Cox-regression modelling. Cost-minimization analysis was undertaken.

Results

One hundred and eighty-one patients were randomized (98 in Centre 1, and 83 in Centre 2): 90 in CAD/CAM and 91 in conventional group. One hundred and fifty three patients attended T24 follow-up. There were no significant differences in LII and arch dimensions between groups for failure-free patients. Within 24 months, 34% maxillary CAD/CAM FRs and 38% maxillary conventional FRs failed, along with 42% mandibular CAD/CAM FRs and 40% mandibular conventional FRs, with no significant difference in survival between groups (hazard ratios conventional to CAD/CAM: maxillary arch: 1.20 [P = 0.46], mandibular arch: 0.98 [P = 0.94]). There were no significant differences in patient satisfaction between groups. No harms were observed. Cost-minimization analysis showed that CAD/CAM FRs were slightly cheaper than conventional FRs.

Conclusions

There were no clinically significant differences in LII, arch widths, and lengths between CAD/CAM and conventional FRs after 24 months. There were no differences in failures and patient satisfaction between groups. CAD/CAM FRs were slightly cheaper than conventional FRs.

Trial registration

ClinicalTrials.gov NCT04389879.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Patient SatisfactionOrthodontic RetainersHumansFollow-Up StudiesOrthodontic Appliance DesignOrthodontic Appliances, Fixed

Stichwörter der Autor:innen

computer-aided design/computer-aided manufacturingcost-minimizationfailure rateorthodontic fixed retainerspatient satisfactionstability

Autor:innen und Institutionen

  • Department of Orthodontics, Institute of Clinical Dentistry, Faculty of Dentistry, University of Oslo, Geitmyrsveien 69/71, Oslo 0455, Norway.
  • Section of Orthodontics, Department of Dentistry and Oral Health, Aarhus University, Vennelyst Boulevard 9, 8000 Aarhus C, Denmark.

ORCID-Profile: Paolo M Cattaneo, Arwa Gera, Marie A Cornelis

Förderung

  • Aarhus University Forskingsfond
  • European Orthodontic Society Research Grant

Zitieren

APA

Pullisaar, H., Cattaneo, P. M., Gera, A., Sankiewicz, M., Bilińska, M., Vandevska-Radunovic, V., & Cornelis, M. A. (2024). Stability, survival, patient satisfaction, and cost-minimization of CAD/CAM versus conventional multistranded fixed retainers in orthodontic patients: a 2-year follow-up of a two-centre randomized controlled trial. European Journal of Orthodontics. https://doi.org/10.1093/ejo/cjae006

Vancouver

Pullisaar H, Cattaneo PM, Gera A, Sankiewicz M, Bilińska M, Vandevska-Radunovic V, et al. Stability, survival, patient satisfaction, and cost-minimization of CAD/CAM versus conventional multistranded fixed retainers in orthodontic patients: a 2-year follow-up of a two-centre randomized controlled trial. European Journal of Orthodontics. 2024. doi:10.1093/ejo/cjae006

BibTeX
@article{Pullisaar2024,
  author = {Pullisaar, Helen and Cattaneo, Paolo M and Gera, Arwa and Sankiewicz, Monika and Bilińska, Małgorzata and Vandevska-Radunovic, Vaska and Cornelis, Marie A},
  title = {Stability, survival, patient satisfaction, and cost-minimization of CAD/CAM versus conventional multistranded fixed retainers in orthodontic patients: a 2-year follow-up of a two-centre randomized controlled trial},
  journal = {European Journal of Orthodontics},
  year = {2024},
  doi = {10.1093/ejo/cjae006}
}
Kostenlos starten →