EUVIMEDEUVIMED entdecken
Crossref

Negative Printing for the Reinforcement of In Situ Tissue-Engineered Cartilage

Stephanie E Doyle, Finn Snow, Carmine Onofrillo, Claudia Di Bella, Cathal D O'Connell, Elena Pirogova, Serena Duchi

Tissue Engineering Part A · 2025

DOI: 10.1089/ten.tea.2023.0358 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Tissue Engineering Part A, 2025. Verfasst von Stephanie E Doyle und 6 weiteren Autor:innen. Beteiligte Einrichtung: Electrical and Biomedical Engineering, School of Engineering, RMIT University, Melbourne, Australia. Hauptthemen laut MEDLINE: Tissue Engineering, Printing, Three-Dimensional, Mesenchymal Stem Cells, Cartilage. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 48 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the realm of in situ cartilage engineering, the targeted delivery of both cells and hydrogel materials to the site of a defect serves to directly stimulate chondral repair. Although the in situ application of stem cell-laden soft hydrogels to tissue defects holds great promise for cartilage regeneration, a significant challenge lies in overcoming the inherent limitation of these soft hydrogels, which must attain mechanical properties akin to the native tissue to withstand physiological loading. We therefore developed a system where a gelatin methacryloyl hydrogel laden with human adipose-derived mesenchymal stem cells is combined with a secondary structure to provide bulk mechanical reinforcement. In this study, we used the negative embodied sacrificial template 3D printing technique to generate eight different lattice-based reinforcement structures made of polycaprolactone, which ranged in porosity from 80% to 90% with stiffnesses from 28 ± 5 kPa to 2853 ± 236 kPa. The most promising of these designs, the hex prism edge, was combined with the cellular hydrogel and retained a stable stiffness over 41 days of chondrogenic differentiation. There was no significant difference between the hydrogel-only and hydrogel scaffold group in the sulfated glycosaminoglycan production (340.46 ± 13.32 µg and 338.92 ± 47.33 µg, respectively) or Type II Collagen gene expression. As such, the use of negative printing represents a promising solution for the integration of bulk reinforcement without losing the ability to produce new chondrogenic matrix.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Tissue EngineeringPrinting, Three-DimensionalMesenchymal Stem CellsCartilageHumansTissue ScaffoldsHydrogelsChondrogenesisPolyestersCell DifferentiationGelatin

Stichwörter der Autor:innen

3D printingcartilagehydrogelstissue engineering

Substanzen

HydrogelspolycaprolactonePolyestersGelatin

Autor:innen und Institutionen

  • Electrical and Biomedical Engineering, School of Engineering, RMIT University, Melbourne, Australia.
  • BioFab3D@ACMD, St Vincent's Hospital Melbourne, Fitzroy, Australia.
  • Department of Surgery, The University of Melbourne, St Vincent's Hospital Melbourne, Fitzroy, Australia.
  • ARC Centre of Excellence for Electromaterials Science, Intelligent Polymer Research Institute, University of Wollongong, Wollongong, Australia.
  • Department of Orthopaedics, St Vincent's Hospital Melbourne, Fitzroy, Australia.

Zitieren

APA

Doyle, S. E., Snow, F., Onofrillo, C., Di Bella, C., O'Connell, C. D., Pirogova, E., & Duchi, S. (2025). Negative Printing for the Reinforcement of In Situ Tissue-Engineered Cartilage. Tissue Engineering Part A. https://doi.org/10.1089/ten.tea.2023.0358

Vancouver

Doyle SE, Snow F, Onofrillo C, Di Bella C, O'Connell CD, Pirogova E, et al. Negative Printing for the Reinforcement of In Situ Tissue-Engineered Cartilage. Tissue Engineering Part A. 2025. doi:10.1089/ten.tea.2023.0358

BibTeX
@article{Doyle2025,
  author = {Doyle, Stephanie E and Snow, Finn and Onofrillo, Carmine and Di Bella, Claudia and O'Connell, Cathal D and Pirogova, Elena and Duchi, Serena},
  title = {Negative Printing for the Reinforcement of In Situ Tissue-Engineered Cartilage},
  journal = {Tissue Engineering Part A},
  year = {2025},
  doi = {10.1089/ten.tea.2023.0358}
}
Kostenlos starten →