Metal Organic Framework-Enhanced 3D-Printed Monoliths for Water Filtration: Tackling Structural Integrity with Higher Adsorption
3D Printing and Additive Manufacturing · 01.10.2026 · 13 (5) · 391-405
DOI: 10.1089/3dp.2024.0262 ↗Kurz gefasst
Fachartikel in der Zeitschrift 3D Printing and Additive Manufacturing, online erschienen am 09.06.2025. Verfasst von Akhter Zia und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, University of Maine, Orono, Maine, USA. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar.
Abstract (Originalsprache)
Access to clean water remains unattainable due to water pollution caused by various sources. Conventional water purification methods fall short of eliminating micro-sized and soluble contaminants, promoting the exploration of innovative approaches utilizing nanomaterials. Thus, metal-organic frameworks (MOFs) have attained considerable attention for water filtration, exhibiting high pollutant adsorption potential due to their abundant and well-organized nanoporous structure. However, a major limitation of MOFs is secondary contamination arising from MOFs leaching and detaching from the substrate on which they are synthesized. Herein, we propose a novel design and manufacturing of MOF-laden monolith 3D structure (MLMS) to minimize such drawbacks. Using extrusion-based additive manufacturing, we constructed the MLMS with macroscale porosity, employing a Moiré pattern to enhance its mechanical strength in different dynamic fluid conditions. Copper-based MOFs (Cu-MOFs) were integrated within the MLMS with high adhesion by the introduction of heat treatment, thereby minimizing leaching and detaching while maintaining the pollutant absorption capability. Furthermore, the Cu-MOFs’ growth, distribution, and adsorption efficiencies have been studied by growing them on various commercially available 3D printing polymers [polylactic acid, polyethylene terephthalate glycol (PETG), acrylonitrile butadiene styrene, and thermoplastic polyurethane]. The results show that the surface area covered by the MOFs ranges from 12.8% to 75.8% depending on the number synthesis cycle. In addition, a reduced leaching rate of 16.1% from the MLMS was observed at a high-water flux (4.14 × 10 3 L m −2 h −1 ), demonstrating significant adhesion between the MLMS and Cu-MOF nanoparticles. The adsorption efficiency of malachite green dye was further analyzed with Cu-MOFs@MLMS, showing removal efficiency of 94.77% and 36.42% under stagnant and dynamic flow (1.18 × 10 3 L m −2 h −1 ) conditions, respectively, when MLMS was made of PETG. The findings reveal the MLMS’ potential in removing contaminants under both stationary and flowing systems and the broad applicability of MOFs-loaded 3D-printed monoliths for scalable and efficient water filtration systems.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Mechanical Engineering, University of Maine, Orono, Maine, USA.
- Advanced Structures & Composites Center, University of Maine, Orono, Maine, USA.
ORCID-Profile: Bashir Khoda
Zitieren
APA
Zia, A., Abbas, S. C., & Khoda, B. (2026). Metal Organic Framework-Enhanced 3D-Printed Monoliths for Water Filtration: Tackling Structural Integrity with Higher Adsorption. 3D Printing and Additive Manufacturing, 13(5), 391-405. https://doi.org/10.1089/3dp.2024.0262
Vancouver
Zia A, Abbas SC, Khoda B. Metal Organic Framework-Enhanced 3D-Printed Monoliths for Water Filtration: Tackling Structural Integrity with Higher Adsorption. 3D Printing and Additive Manufacturing. 2026;13(5):391-405. doi:10.1089/3dp.2024.0262
BibTeX
@article{Zia2026,
author = {Zia, Akhter and Abbas, Syed Comail and Khoda, Bashir},
title = {Metal Organic Framework-Enhanced 3D-Printed Monoliths for Water Filtration: Tackling Structural Integrity with Higher Adsorption},
journal = {3D Printing and Additive Manufacturing},
year = {2026},
volume = {13},
number = {5},
pages = {391--405},
doi = {10.1089/3dp.2024.0262}
}
EUVIMED