EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Improved Productivity with Multilaser Rotary Powder Bed Fusion Additive Manufacturing

Peter Wang iD, Gordon Robertson, Brian T Gibson, Chris M Fancher, Jay Reynolds, Michael Borish, Jesus R Cruz, Phillip Chesser, Benjamin Stump, Amiee Jackson, Eric MacDonald iD

3D Printing and Additive Manufacturing · 01.02.2024 · 11 (1) · 231-241

DOI: 10.1089/3dp.2022.0288 ↗

Kurz gefasst

Fachartikel in der Zeitschrift 3D Printing and Additive Manufacturing, online erschienen am 15.02.2024. Verfasst von Peter Wang und 10 weiteren Autor:innen. Beteiligte Einrichtung: Manufacturing Science Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee, USA. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Laser powder bed fusion (LPBF) enables the fabrication of intricate, geometrically complex structures with a sufficiently fine surface finish for many engineering applications with a diversity of available feedstock metals. However, the production rate of LPBF systems is not well suited for mass production in comparison to traditional manufacturing methods. LPBF systems measure their deposition rates in 100's of grams per hour, while other processes measure in kilograms per hour or even in the case of processes such as forming, stamping, and casting, 100's of kilograms per hour. To be widely adopted in industry for mass production, LPBF requires a new scalable architecture that enables many orders of magnitude improvement in deposition rate, while maintaining the geometry freedom of additive manufacturing. This article explores concepts that could achieve as much as four orders of magnitude increase in the production rate through the application of (1) rotary table kinematic arrangements; (2) a dramatic number of simultaneously operating lasers; (3) reductions of laser optic size; (4) improved scanning techniques; and (5) an optimization of toroidal build plate size. To theoretically demonstrate the possibilities of production improvements, a productivity analysis is proposed for synchronous reluctance motors with relevance to the electric vehicle industry, given the recent increase in the diversity of printable soft magnetic alloys. The analysis provides insights into the impact of the architecture and process parameters necessary to optimize rotary powder bed fusion for mass production.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingmass productionrotary powder bed fusion

Autor:innen und Institutionen

  • Manufacturing Science Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee, USA.
  • Material Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee, USA.
  • The University of Texas at El Paso, El Paso, Texas, USA.
  • Computational Sciences and Engineering Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee, USA.

ORCID-Profile: Peter Wang, Eric MacDonald

Zitieren

APA

Wang, P., Robertson, G., Gibson, B. T., Fancher, C. M., Reynolds, J., Borish, M., Cruz, J. R., Chesser, P., Stump, B., Jackson, A., & MacDonald, E. (2024). Improved Productivity with Multilaser Rotary Powder Bed Fusion Additive Manufacturing. 3D Printing and Additive Manufacturing, 11(1), 231-241. https://doi.org/10.1089/3dp.2022.0288

Vancouver

Wang P, Robertson G, Gibson BT, Fancher CM, Reynolds J, Borish M, et al. Improved Productivity with Multilaser Rotary Powder Bed Fusion Additive Manufacturing. 3D Printing and Additive Manufacturing. 2024;11(1):231-241. doi:10.1089/3dp.2022.0288

BibTeX
@article{Wang2024,
  author = {Wang, Peter and Robertson, Gordon and Gibson, Brian T and Fancher, Chris M and Reynolds, Jay and Borish, Michael and Cruz, Jesus R and Chesser, Phillip and Stump, Benjamin and Jackson, Amiee and MacDonald, Eric},
  title = {Improved Productivity with Multilaser Rotary Powder Bed Fusion Additive Manufacturing},
  journal = {3D Printing and Additive Manufacturing},
  year = {2024},
  volume = {11},
  number = {1},
  pages = {231--241},
  doi = {10.1089/3dp.2022.0288}
}
Kostenlos starten →