EUVIMEDEUVIMED entdecken
Open Access

Evaluation of Tensile Strength and Repeatability of 3D Printed Carbon Fiber Materials and Processes

Abigail Batley iD, Richard Glithro, Bryce Dyer, Philip Sewell

3D Printing and Additive Manufacturing · 01.10.2024 · 11 (5) · 1691-1702

DOI: 10.1089/3dp.2022.0262 ↗

Kurz gefasst

Fachartikel in der Zeitschrift 3D Printing and Additive Manufacturing, online erschienen am 22.10.2024. Verfasst von Abigail Batley und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Design and Engineering, Faculty of Science and Technology, Bournemouth University, Poole, United Kingdom. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

As additive manufacturing (AM) with composite materials becomes more widely used in industry to create high-strength components, it is vital to have quantified material properties that provide designers and engineers accurate data to decide which materials are suitable for their applications. This study replicates the build processes and tensile tests undertaken by AM material manufacturers to compare tensile strengths achieved with those stated on the manufacturers' data sheets. These are important data to research and analyze as either it will corroborate properties given by the manufacturers and provide confidence in the values provided or it will show that the manufacturer's values cannot always be achieved and that designers and engineers must be more critical about the values manufacturers are providing when using the materials in their own applications. Tensile tests were performed on additively manufactured specimens that had been built using the same parameters that were used during the manufacturers' testing procedures. Digital image correlation was used to accurately measure strain in the test samples, enabling material properties to be determined. Microscopy analysis enabled the visual inspection of the print quality, the identification of defects, and the determination of volume fraction with the samples. The results show inconsistencies between the tensile strength results achieved during this study and the tensile strengths stated by the manufacturers. The results show that two materials exceeded the expected values and one material did not reach the expected value. Analysis of the 3D printed specimens shows that poor fiber–matrix wetting, large voids, and weak interfacial bonding were accountable for the lower-than-expected tensile strength results. While good print quality, low void percentage, proper fiber–matrix wetting, and good control measures were accountable for results that exceeded expectation. These results show that designers and engineers cannot solely rely on material data sheets to establish the mechanical properties of their 3D printed components.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingcarbon fibercomposite 3D printingrepeatabilitytensile strength

Autor:innen und Institutionen

  • Department of Design and Engineering, Faculty of Science and Technology, Bournemouth University, Poole, United Kingdom.
  • Office of the Vice-Chancellor, Bournemouth University, Poole, United Kingdom.

ORCID-Profile: Abigail Batley

Zitieren

APA

Batley, A., Glithro, R., Dyer, B., & Sewell, P. (2024). Evaluation of Tensile Strength and Repeatability of 3D Printed Carbon Fiber Materials and Processes. 3D Printing and Additive Manufacturing, 11(5), 1691-1702. https://doi.org/10.1089/3dp.2022.0262

Vancouver

Batley A, Glithro R, Dyer B, Sewell P. Evaluation of Tensile Strength and Repeatability of 3D Printed Carbon Fiber Materials and Processes. 3D Printing and Additive Manufacturing. 2024;11(5):1691-1702. doi:10.1089/3dp.2022.0262

BibTeX
@article{Batley2024,
  author = {Batley, Abigail and Glithro, Richard and Dyer, Bryce and Sewell, Philip},
  title = {Evaluation of Tensile Strength and Repeatability of 3D Printed Carbon Fiber Materials and Processes},
  journal = {3D Printing and Additive Manufacturing},
  year = {2024},
  volume = {11},
  number = {5},
  pages = {1691--1702},
  doi = {10.1089/3dp.2022.0262}
}
Kostenlos starten →