EUVIMEDEUVIMED entdecken
Open Access

Durability of Vacuum Infusion Tooling Produced from Fused Granular Fabrication Additive Manufacturing

Nathan Northrup, Jason M Weaver iD, Andrew R George

3D Printing and Additive Manufacturing · 01.04.2024 · 11 (2) · 508-516

DOI: 10.1089/3dp.2022.0130 ↗

Kurz gefasst

Fachartikel in der Zeitschrift 3D Printing and Additive Manufacturing, online erschienen am 16.04.2024. Verfasst von Nathan Northrup und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Manufacturing Engineering, Brigham Young University, Provo, Utah, USA. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 27 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Fused Granular Fabrication Additive Manufacturing (FGF AM) has the capability to create tooling that is lower cost than conventionally manufactured tooling and still has sufficient properties for many applications. A vacuum infusion (VI) mold was printed from fiberglass-acrylonitrile butadiene styrene (ABS) and evaluated for wear and suitability for small VI runs. The mold was designed to accentuate high wear as a “worst case” scenario. The mold was able to produce 10 parts successfully before any noticeable change occurred to the surface finish. By 14 parts, the surface finish had roughened sufficiently that demolding was difficult and resulted in damage to the part. Profilometry measurements showed a 7 × increase in roughness over the run. No significant tool wear or change in geometry was detected. Even longer life would be expected for typical tooling designs since the test mold was deliberately designed to accentuate wear and demolding issues. Based on these results, similar FGF molds are a feasible option for short run VI production for prototyping or low-volume composites manufacturing, possibly at lower cost and quicker turnaround time than machined aluminum molds.

Schlagwörter

Stichwörter der Autor:innen

VARTMcompositesdurabilityfused granular fabricationhybrid manufacturinglarge area additive manufacturingsurface finishtooling designvacuum infusionwear

Autor:innen und Institutionen

  • Department of Manufacturing Engineering, Brigham Young University, Provo, Utah, USA.

ORCID-Profile: Jason M Weaver

Zitieren

APA

Northrup, N., Weaver, J. M., & George, A. R. (2024). Durability of Vacuum Infusion Tooling Produced from Fused Granular Fabrication Additive Manufacturing. 3D Printing and Additive Manufacturing, 11(2), 508-516. https://doi.org/10.1089/3dp.2022.0130

Vancouver

Northrup N, Weaver JM, George AR. Durability of Vacuum Infusion Tooling Produced from Fused Granular Fabrication Additive Manufacturing. 3D Printing and Additive Manufacturing. 2024;11(2):508-516. doi:10.1089/3dp.2022.0130

BibTeX
@article{Northrup2024,
  author = {Northrup, Nathan and Weaver, Jason M and George, Andrew R},
  title = {Durability of Vacuum Infusion Tooling Produced from Fused Granular Fabrication Additive Manufacturing},
  journal = {3D Printing and Additive Manufacturing},
  year = {2024},
  volume = {11},
  number = {2},
  pages = {508--516},
  doi = {10.1089/3dp.2022.0130}
}
Kostenlos starten →