EUVIMEDEUVIMED entdecken
Open Access

Mechanical Properties, Microstructure, and Actuation Behavior of Wire Arc Additive Manufactured Nitinol: Titanium Bimetallic Structures

Shalini Singh iD, Elena Demidova, Natalia Resnina, Sergey Belyaev, I A Palani, C P Paul, Ajit Kumar, K G Prashanth

3D Printing and Additive Manufacturing · 01.02.2024 · 11 (1) · 143-151

DOI: 10.1089/3dp.2021.0324 ↗

Kurz gefasst

Fachartikel in der Zeitschrift 3D Printing and Additive Manufacturing, online erschienen am 15.02.2024. Verfasst von Shalini Singh und 7 weiteren Autor:innen. Beteiligte Einrichtung: Mechatronics and Instrumentation Laboratory, Department of Mechanical Engineering, Indian Institute of Technology Indore, Indore, India. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 24 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Nitinol (NiTi) is well known for its corrosion resistance, shape memory effect, superelasticity, and biocompatibility, whereas Titanium (Ti) is well known for its high specific strength, corrosion resistance, and biocompatibility. The bimetallic joint of NiTi and Ti is required for applications that require tailored properties at different locations within the same component, as well as to increase design flexibility while reducing material costs. However, because of the formation of brittle intermetallic phases, connecting NiTi and Ti is difficult. In the present study, a systematic experimental investigation is carried out to develop NiTi–Ti bimetallic joint using wire arc additive manufacturing (WAAM) for the first time and to evaluate its microstructure, mechanical properties, martensitic transformation, and actuation behavior in the as-built condition. The defect-free joint is obtained through WAAM and microstructural studies indicate the formation of intermetallics at the NiTi–Ti interface leading to higher microhardness values (600 HV). Shape recovery behavior and phase transformation temperature were also enhanced in comparison to NiTi. An improved actuation and bending angle recovery is observed in comparison with NiTi. The present study lays the way for the use of WAAM in the construction of NiTi and Ti bimetallic structures for engineering and medicinal applications.

Schlagwörter

Stichwörter der Autor:innen

Nitinolbimetallic jointshape memory alloyswall structurewire arc additive manufacturing

Autor:innen und Institutionen

  • Mechatronics and Instrumentation Laboratory, Department of Mechanical Engineering, Indian Institute of Technology Indore, Indore, India.
  • Saint-Petersburg State University, Saint-Petersburg, Russian Federation.
  • Raja Ramanna Center for Advanced Technology, Indore, India.
  • Homi Bhabha National Institute, Anushaktinagar, Mumbai, India.
  • Department of Mechanical and Industrial Engineering, Tallinn University of Technology, Tallinn, Estonia.
  • Erich Schmid Institute of Materials Science, Austrian Academy of Sciences, Leoben, Austria.

ORCID-Profile: Shalini Singh

Zitieren

APA

Singh, S., Demidova, E., Resnina, N., Belyaev, S., Palani, I. A., Paul, C. P., Kumar, A., & Prashanth, K. G. (2024). Mechanical Properties, Microstructure, and Actuation Behavior of Wire Arc Additive Manufactured Nitinol: Titanium Bimetallic Structures. 3D Printing and Additive Manufacturing, 11(1), 143-151. https://doi.org/10.1089/3dp.2021.0324

Vancouver

Singh S, Demidova E, Resnina N, Belyaev S, Palani IA, Paul CP, et al. Mechanical Properties, Microstructure, and Actuation Behavior of Wire Arc Additive Manufactured Nitinol: Titanium Bimetallic Structures. 3D Printing and Additive Manufacturing. 2024;11(1):143-151. doi:10.1089/3dp.2021.0324

BibTeX
@article{Singh2024,
  author = {Singh, Shalini and Demidova, Elena and Resnina, Natalia and Belyaev, Sergey and Palani, I A and Paul, C P and Kumar, Ajit and Prashanth, K G},
  title = {Mechanical Properties, Microstructure, and Actuation Behavior of Wire Arc Additive Manufactured Nitinol: Titanium Bimetallic Structures},
  journal = {3D Printing and Additive Manufacturing},
  year = {2024},
  volume = {11},
  number = {1},
  pages = {143--151},
  doi = {10.1089/3dp.2021.0324}
}
Kostenlos starten →