EUVIMEDEUVIMED entdecken
Open Access

Study of Low-Pressure Cold Spray Additive Manufacturing: Investigation of Kinematic Spray Parameters on Deposition and Properties

Wenbo Li iD, Hongjian Wu iD, Christophe Verdy, Sophie Costil, Hanlin Liao, Sihao Deng

3D Printing and Additive Manufacturing · 01.12.2023 · 10 (6) · 1260-1271

DOI: 10.1089/3dp.2021.0260 ↗

Kurz gefasst

Fachartikel in der Zeitschrift 3D Printing and Additive Manufacturing, online erschienen am 11.12.2023. Verfasst von Wenbo Li und 5 weiteren Autor:innen. Beteiligte Einrichtung: ICB UMR 6303, CNRS, Univ. Bourgogne Franche-Comté, UTBM, Belfort, France. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Low-pressure cold spray (LPCS) has broadened the application field of cold spray owing to its portability and low cost. For additive manufacturing (AM) based on LPCS (LPCSAM), it is important to investigate the effects of parameters such as temperature and pressure of the gas, stand-off distance, gun traverse speed, and the number of scanning passes of the gun on the deposition and properties. This study aims to determine the optimal kinematic spray parameters for spraying Cu+Al 2 O 3 powder onto an aluminum substrate through LPCS, so as to prepare for the next AM work. The deposition mass, deposition rate, microhardness, and roughness under different spraying conditions were studied. The best spraying effect, with a high deposition rate and without nozzle clogging, was obtained at a nitrogen pressure of 0.9 MPa and a temperature of 400°C.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingcold spraylow pressurescanning passspraying distancevelocity

Autor:innen und Institutionen

  • ICB UMR 6303, CNRS, Univ. Bourgogne Franche-Comté, UTBM, Belfort, France.
  • Institute of Materials Technology, Helmut-Schmidt-University/University of the Federal Armed Forces Hamburg, Hamburg, Germany.

ORCID-Profile: Wenbo Li, Hongjian Wu

Zitieren

APA

Li, W., Wu, H., Verdy, C., Costil, S., Liao, H., & Deng, S. (2023). Study of Low-Pressure Cold Spray Additive Manufacturing: Investigation of Kinematic Spray Parameters on Deposition and Properties. 3D Printing and Additive Manufacturing, 10(6), 1260-1271. https://doi.org/10.1089/3dp.2021.0260

Vancouver

Li W, Wu H, Verdy C, Costil S, Liao H, Deng S. Study of Low-Pressure Cold Spray Additive Manufacturing: Investigation of Kinematic Spray Parameters on Deposition and Properties. 3D Printing and Additive Manufacturing. 2023;10(6):1260-1271. doi:10.1089/3dp.2021.0260

BibTeX
@article{Li2023,
  author = {Li, Wenbo and Wu, Hongjian and Verdy, Christophe and Costil, Sophie and Liao, Hanlin and Deng, Sihao},
  title = {Study of Low-Pressure Cold Spray Additive Manufacturing: Investigation of Kinematic Spray Parameters on Deposition and Properties},
  journal = {3D Printing and Additive Manufacturing},
  year = {2023},
  volume = {10},
  number = {6},
  pages = {1260--1271},
  doi = {10.1089/3dp.2021.0260}
}
Kostenlos starten →