Graphene oxide and in-situ carbon reinforced hydroxyapatite scaffolds via ultraviolet-curing 3D printing technology with high osteoinductivity for bone regeneration
Biofabrication · 01.04.2025 · 17 (2) · 025028
DOI: 10.1088/1758-5090/adbcdd ↗Kurz gefasst
Fachartikel in der Zeitschrift Biofabrication, online erschienen am 20.03.2025. Verfasst von Hongyu Zhao und 8 weiteren Autor:innen. Beteiligte Einrichtung: Centre of Stomatology, The Second Hospital, Cheeloo College of Medicine, Shandong University, Jinan 250033, People's Republic of China. Hauptthemen laut MEDLINE: Graphite, Bone Regeneration, Durapatite, Tissue Scaffolds. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 68 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Natural Science Foundation of Shandong Province, Key Technologies Research and Development Program.
Abstract (Originalsprache)
Ultraviolet photopolymerization additive manufacturing has been used to fabricate calcium phosphate (Ca-P) ceramic scaffolds for repairing bone defects, but it is still a challenge for 3D printed Ca-P scaffolds to simultaneously enhance the mechanical strength and osteoinductivity. Here, we successfully developed a high-performance hydroxyapatite (HA) scaffold containing in-situ carbon and graphene oxide (GO) by precisely regulating the degreasing and sintering atmosphere. The results indicated that the mechanical properties of HA scaffolds could be significantly improved by regulating the amount of in-situ carbon. The HA scaffold containing 0.27 wt.% carbon achieved the maximum compressive strength of 12.5 MPa with a porosity of approximately 70%. The RNA transcriptome sequencing analysis revealed that in-situ carbon could promote osteogenic differentiation by improving oxygen transport and promoting the expression of multiple angiogenic factors. More importantly, in the absence of osteoinductive agents, the in-situ carbon and GO synergistically promoted more effective bone mineralization, demonstrating enhanced osteoinductivity in vitro. In a rodent model, the bioceramic scaffolds also exhibited improved osteogenesis in critical bone defects. Therefore, in-situ carbon and GO could simultaneously enhance the mechanical strength and osteoinductivity of HA scaffolds, effectively achieving substantial endogenous bone regeneration. This strategy will provide a simple and energy-efficient approach for engineering osteoinductive ceramic scaffolds for repairing bone defects.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Centre of Stomatology, The Second Hospital, Cheeloo College of Medicine, Shandong University, Jinan 250033, People's Republic of China.
- School and Hospital of Stomatology, Cheeloo College of Medicine, Shandong University, Jinan 250012, People's Republic of China.
- School of Mechanical and Electronic Engineering, Shandong Jianzhu University, Jinan, People's Republic of China.
- Center for Advanced Jet Engineering Technology (CaJET), School of Mechanical Engineering, Shandong University, Jinan 250061, People's Republic of China.
- Key Laboratory of High Efficiency and Clean Mechanical Manufacture, Shandong University, Ministry of Education, Jinan 250061, People's Republic of China.
- National Demonstration Center for Experimental Mechanical Engineering Education (Shandong University), Shandong, People's Republic of China.
ORCID-Profile: Qingguo Lai
Förderung
- Natural Science Foundation of Shandong Province
- Key Technologies Research and Development Program
Zitieren
APA
Zhao, H., Niu, X., Wei, S., Lin, W., Luo, H., Zou, B., Chen, Q., Xing, H., & Lai, Q. (2025). Graphene oxide and in-situ carbon reinforced hydroxyapatite scaffolds via ultraviolet-curing 3D printing technology with high osteoinductivity for bone regeneration. Biofabrication, 17(2), 025028. https://doi.org/10.1088/1758-5090/adbcdd
Vancouver
Zhao H, Niu X, Wei S, Lin W, Luo H, Zou B, et al. Graphene oxide and in-situ carbon reinforced hydroxyapatite scaffolds via ultraviolet-curing 3D printing technology with high osteoinductivity for bone regeneration. Biofabrication. 2025;17(2):025028. doi:10.1088/1758-5090/adbcdd
BibTeX
@article{Zhao2025,
author = {Zhao, Hongyu and Niu, Xiao and Wei, Shitong and Lin, Wei and Luo, Hao and Zou, Bin and Chen, Qinghua and Xing, Hongyu and Lai, Qingguo},
title = {Graphene oxide and in-situ carbon reinforced hydroxyapatite scaffolds via ultraviolet-curing 3D printing technology with high osteoinductivity for bone regeneration},
journal = {Biofabrication},
year = {2025},
volume = {17},
number = {2},
pages = {025028},
doi = {10.1088/1758-5090/adbcdd}
}
EUVIMED