EUVIMEDEUVIMED entdecken
Crossref

Numerical and experimental investigation of residual stress polarity and distortion evolution in laser powder bed fusion of IN718 spur gears

Vikram Kumar Gupta, Sanjay Kumar Chaturvedi, Rajiv Nandan Rai

Modelling and Simulation in Materials Science and Engineering · 31.07.2026 · 34 (5) · 055005

DOI: 10.1088/1361-651x/ae798f ↗

Kurz gefasst

Fachartikel in der Zeitschrift Modelling and Simulation in Materials Science and Engineering, online erschienen am 22.06.2026. Verfasst von Vikram Kumar Gupta und 2 weiteren Autor:innen. Die Arbeit nennt 45 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Residual stress and distortion remain critical challenges in the laser powder bed fusion (L-PBF) additive manufacturing of complex load-bearing components such as spur gears, particularly for high-performance alloys like Inconel 718 (IN718). In this study, a comprehensive numerical-experimental framework is developed to investigate the evolution of residual stress and deformation in an L-PBF-manufactured IN718 spur gear, with explicit consideration of process parameters, thermal history, and geometric constraints. A thermo-mechanical simulation strategy was implemented using ansys additive print to model layer-wise heat transfer, stress evolution, and distortion. Two contrasting parameter sets were considered, involving variations in laser power, layer thickness, scan speed, scan orientation, and bed temperature. Spatial distributions of normal and shear stress components, Von Mises equivalent stress, and maximum deformation were analyzed along the build height to elucidate stress polarity, accumulation mechanisms, and distortion sensitivity. Simulation results reveal a pronounced transition from a compression-dominated residual stress field under higher energy input and elevated bed temperature to a tensile-dominated stress state under reduced thermal buffering and orthogonal scan rotation. The adverse parameter set resulted in a 10.5% increase in peak residual stress and nearly a fivefold rise in deformation, highlighting the compounded influence of layer thickness, scan orientation, and substrate temperature. Correlation analysis further demonstrates that build-direction stress components strongly govern residual stress accumulation, while deformation shows limited coupling with in-plane stresses. Experimental validation was conducted on an IN718 spur gear fabricated using optimized parameters on an EOS M280 system. X-ray diffraction (sin 2 ψ) measurements confirmed a compressive surface residual stress state (588 MPa), closely aligning with the numerically predicted low-stress regime. Dimensional inspection indicated excellent geometric fidelity, with a maximum deviation of 0.20 mm. Comparative stress–deformation performance mapping demonstrates that the experimental build occupies a favorable low-stress, low-distortion domain, validating the predictive capability of the simulation framework. The proposed integrated methodology provides robust insights for process parameter selection and offers a reliable pathway for residual stress mitigation and distortion.

Zitieren

APA

Gupta, V. K., Chaturvedi, S. K., & Rai, R. N. (2026). Numerical and experimental investigation of residual stress polarity and distortion evolution in laser powder bed fusion of IN718 spur gears. Modelling and Simulation in Materials Science and Engineering, 34(5), 055005. https://doi.org/10.1088/1361-651x/ae798f

Vancouver

Gupta VK, Chaturvedi SK, Rai RN. Numerical and experimental investigation of residual stress polarity and distortion evolution in laser powder bed fusion of IN718 spur gears. Modelling and Simulation in Materials Science and Engineering. 2026;34(5):055005. doi:10.1088/1361-651x/ae798f

BibTeX
@article{Gupta2026,
  author = {Gupta, Vikram Kumar and Chaturvedi, Sanjay Kumar and Rai, Rajiv Nandan},
  title = {Numerical and experimental investigation of residual stress polarity and distortion evolution in laser powder bed fusion of IN718 spur gears},
  journal = {Modelling and Simulation in Materials Science and Engineering},
  year = {2026},
  volume = {34},
  number = {5},
  pages = {055005},
  doi = {10.1088/1361-651x/ae798f}
}
Kostenlos starten →