Effects of alkali-metal deposition on the thermometric performance of YAG:Dy phosphor in a simulated high-alkali combustion environment
Measurement Science and Technology · 06.11.2026 · 37 (44) · 445202
DOI: 10.1088/1361-6501/aeb712 ↗Kurz gefasst
Fachartikel in der Zeitschrift Measurement Science and Technology, online erschienen am 05.11.2026. Verfasst von Xiaoqi Wang und 9 weiteren Autor:innen. Die Arbeit nennt 32 Literaturangaben. Gefördert von: R&D funding of Xinjiang, National Natural Science Foundation of China, National Key R&D Program of China.
Abstract (Originalsprache)
Ash deposition and slagging during high-alkali coal and biomass combustion disturb heat transfer over boiler heating surfaces and can cause localized overheating, making reliable surface-temperature measurement critical. Laser-induced phosphorescence thermometry offers fast-response, two-dimensional measurement in harsh combustion environments, but deposited alkali-metal species may alter the optical and thermometric response of phosphor coatings. Here, NaCl and Na 2 CO 3 were deposited onto YAG:Dy coatings in a two-stage tube furnace and a homogeneous burner, and the thermometric response of the exposed coatings was then measured by heating in an electric furnace, with SEM–EDS, phosphorescence spectroscopy, and XRD used to characterize the accompanying changes. Both the 458 nm and 497 nm emissions were progressively attenuated by deposition, becoming pronounced at and above 600 °C and stronger at the higher NaCl loading. Despite this loss of absolute signal, the intensity ratio I 458 / I 497 remained close to that of the original coating below approximately 600 °C and deviated markedly above it, especially after prolonged burner exposure. Emission spectra showed that at 800 °C the fine structure within 450–500 nm was no longer resolved after normalization to the 458 nm band, indicating that exposure altered the relative spectral distribution on which the ratio depends. SEM–EDS showed Na enrichment throughout the analysed regions, and XRD revealed weak additional reflections tentatively consistent with a sodium-containing aluminate phase. The results show that YAG:Dy ratio thermometry remains reliable only for surfaces whose temperature does not exceed approximately 600 °C. Above this range, alkali-induced ratio deviations become substantial and, under severe exposure, the ratio–temperature relation can become non-monotonic, so a measured ratio no longer corresponds to a unique temperature.
Förderung
- R&D funding of Xinjiang
- National Natural Science Foundation of China
- National Key R&D Program of China
Zitieren
APA
Wang, X., Huang, Y., Weng, W., Ji, P., Li, Y., Liu, S., He, Y., Li, Q., Li, P., & Wang, Z. (2026). Effects of alkali-metal deposition on the thermometric performance of YAG:Dy phosphor in a simulated high-alkali combustion environment. Measurement Science and Technology, 37(44), 445202. https://doi.org/10.1088/1361-6501/aeb712
Vancouver
Wang X, Huang Y, Weng W, Ji P, Li Y, Liu S, et al. Effects of alkali-metal deposition on the thermometric performance of YAG:Dy phosphor in a simulated high-alkali combustion environment. Measurement Science and Technology. 2026;37(44):445202. doi:10.1088/1361-6501/aeb712
BibTeX
@article{Wang2026,
author = {Wang, Xiaoqi and Huang, Yu and Weng, Wubin and Ji, Peng and Li, Yang and Liu, Siyu and He, Yong and Li, Quanhuan and Li, Peng and Wang, Zhihua},
title = {Effects of alkali-metal deposition on the thermometric performance of YAG:Dy phosphor in a simulated high-alkali combustion environment},
journal = {Measurement Science and Technology},
year = {2026},
volume = {37},
number = {44},
pages = {445202},
doi = {10.1088/1361-6501/aeb712}
}
EUVIMED