Characterisation, Simulation and Optimisation of a Gridless LaB 6 Hollow Cathode DC Plasma Source for Plasma Ion Assisted Electron Beam Deposition of Optical Coatings
Journal of Physics D: Applied Physics · 19.11.2026
DOI: 10.1088/1361-6463/aec45d ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Physics D: Applied Physics, online erschienen am 19.11.2026. Verfasst von Connor Lindsay und 4 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Royal Academy of Engineering, Science and Technology Facilities Council.
Abstract (Originalsprache)
The Plasma Deposition Source (PDS) is a gridless source for Plasma Ion Assisted Deposition (PIAD) of electron beam evaporated optical coatings. PDS geometry, electrical and water-cooling feedthroughs provides a retrofittable configuration to most vacuum deposition chambers. PDS utilises an inductively heated (100kHz) LaB6 hot hollow cathode providing large surface area thermionic emission of a dc glow discharge at low deposition chamber vacuum pressure (typically 2 ×10 -4 mbar). The PDS incorporates a pressure differential between axially separated cathode and anode regions with typically 2 ×10 -3 mbar and 2 x10 -4 mbar pressures respectively, providing enhanced LaB6 hollow cathode performance, self sustaining plasma operation, reduced substrate heat loading and particulate contamination from the cathode. Retarding Field Energy Analyzer and Langmuir probe plasma diagnostic measurements and Monte Carlo simulation are described, used to characterise, optimise plasma output and establish fundamental understanding of PDS operation. PDS provides optimal ion energy range (5 to 50eV), and enhanced ion current density (~0.4mA/cm 2 at 90cm distance from the PDS to substrates) suitable for PIAD of densified amorphous optical thin films. Controllable PIAD over extended deposition area is achieved using a tunable magnetic field provided by a solenoid formed axially on the exterior of the anode assembly. Automated PDS control is described providing stable output of plasma ion energy and current density. PIAD of densified single TiO2 and SiO2 layers (typical deposition rates 0.6 and 0.7 nm/sec respectively) is demonstrated as a function of PDS parameters and plasma ion adatom arrival rate. Influence of the impinging plasma ions is shown to be a momentum transfer based thresholding process, where a minimum ion current density is required to achieve film densification with ion to deposited adatom ratio typically ≥1.2. Also PIAD of an eleven-layer TiO2/ SiO2 multilayer notch filter with no spectral drift over extended substrate deposition area is demonstrated.
Förderung
- Royal Academy of Engineering
- Science and Technology Facilities Council
Zitieren
APA
Lindsay, C., Brinkley, I., Clark, C., Mao, N., & Gibson, D. (2026). Characterisation, Simulation and Optimisation of a Gridless LaB 6 Hollow Cathode DC Plasma Source for Plasma Ion Assisted Electron Beam Deposition of Optical Coatings. Journal of Physics D: Applied Physics. https://doi.org/10.1088/1361-6463/aec45d
Vancouver
Lindsay C, Brinkley I, Clark C, Mao N, Gibson D. Characterisation, Simulation and Optimisation of a Gridless LaB 6 Hollow Cathode DC Plasma Source for Plasma Ion Assisted Electron Beam Deposition of Optical Coatings. Journal of Physics D: Applied Physics. 2026. doi:10.1088/1361-6463/aec45d
BibTeX
@article{Lindsay2026,
author = {Lindsay, Connor and Brinkley, Ian and Clark, Caspar and Mao, Nianxin and Gibson, Des},
title = {Characterisation, Simulation and Optimisation of a Gridless LaB 6 Hollow Cathode DC Plasma Source for Plasma Ion Assisted Electron Beam Deposition of Optical Coatings},
journal = {Journal of Physics D: Applied Physics},
year = {2026},
doi = {10.1088/1361-6463/aec45d}
}
EUVIMED