Passive stabilization of simultaneous droplet generation in a double T-junction microfluidic device
Journal of Micromechanics and Microengineering · 17.11.2026
DOI: 10.1088/1361-6439/aec301 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Micromechanics and Microengineering, online erschienen am 17.11.2026. Verfasst von Jonathan Ulises Ulises Álvarez-Martínez und 1 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Secretaría de Ciencia, Humanidades, Tecnología e Innovación, Dirección de Apoyo a la Investigación y el Posgrado.
Abstract (Originalsprache)
Stable simultaneous droplet generation remains challenging because hydraulic coupling between interconnected generators can produce pressure disturbances that affect dropletformation and uniformity. Here, we investigate a double T-junction microfluidic device 
incorporating a downstream ellipsoidal expansion designed to redistribute the pressure field through a gradual variation in hydraulic resistance. Three-dimensional two-phase-flow simulations were performed using COMSOL Multiphysics to investigate droplet formation and downstream pressure redistribution. An analytical hydraulic model was also developed to describe the nonlinear pressure redistribution introduced by the ellipsoidal expansion. Experimental validation was performed using a fabricated polydimethylsiloxane (PDMS) device with water and methanol as dispersed phases (Qd) and mineral oil as the continuous phase (Qc). Four flow-rate ratios, FRR = Qd/Qc = 0.25, 0.50, 0.75, and 1.00, were investigated at a fixed continuous-phase flow rate of Qc = 70µLmin−1. Across the complete experimental dataset, 57,076 individual microdroplets were analyzed. Both fluid systems exhibited a positive linear dependence of Ld/w on the flow-rate ratio, consistent with squeezing-regime droplet formation. For the water oil system (WOS), the numerical and experimental scaling slopes were 0.42 and 1.13, respectively, whereas the methanol oil system (MOS) exhibited particularly close quantitative agreement, with corresponding slopes of 0.68 and 0.66. The experimental relationships remained strongly linear, with R2 =0.98 for WOS and R2 =0.96 for MOS. Statistical characterization further revealed fluid-dependent behavior, with the MOS maintaining a comparatively low coefficient of variation of approximately 7–8% over the investigated operating range. An otherwise equivalent reference device without the downstream ellipsoidal expansion was also experimentally evaluated. Under the same nominal operating conditions, the continuous mineral oil phase flowed through the main channel, whereas the dispersed phases did not advance sufficiently into the T-junctions to establish sustained channel blockage and droplet pinch-off. In contrast, the chamber-equipped device sustained simultaneous droplet generation for both Qd. These results support the ellipsoidal expansion as a passive
geometric pressure-redistribution strategy that contributes to sustaining simultaneous droplet generation while reducing the effects associated with hydraulic coupling and preserving the characteristic droplet-length scaling behavior of the squeezing regime.
Förderung
- Secretaría de Ciencia, Humanidades, Tecnología e Innovación
- Dirección de Apoyo a la Investigación y el Posgrado
Zitieren
APA
Álvarez-Martínez, J. U. U., & Castro-Beltrán, R. (2026). Passive stabilization of simultaneous droplet generation in a double T-junction microfluidic device. Journal of Micromechanics and Microengineering. https://doi.org/10.1088/1361-6439/aec301
Vancouver
Álvarez-Martínez JUU, Castro-Beltrán R. Passive stabilization of simultaneous droplet generation in a double T-junction microfluidic device. Journal of Micromechanics and Microengineering. 2026. doi:10.1088/1361-6439/aec301
BibTeX
@article{lvarezMartnez2026,
author = {Álvarez-Martínez, Jonathan Ulises Ulises and Castro-Beltrán, Rigoberto},
title = {Passive stabilization of simultaneous droplet generation in a double T-junction microfluidic device},
journal = {Journal of Micromechanics and Microengineering},
year = {2026},
doi = {10.1088/1361-6439/aec301}
}
EUVIMED