EUVIMEDEUVIMED entdecken
Crossref

The effects of 3D printing designs on PLA polymer flexural and fatigue strength

Pham Son Minh, Van-Thuc Nguyen, Tran Minh The Uyen, Thanh Trung Do, Anh Duong Thi Van, Hai Nguyen Le Dang

Journal of Micromechanics and Microengineering · 01.06.2024 · 34 (6) · 065004

DOI: 10.1088/1361-6439/ad4b2a ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Micromechanics and Microengineering, online erschienen am 24.05.2024. Verfasst von Pham Son Minh und 5 weiteren Autor:innen. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 34 Literaturangaben. Gefördert von: Ho Chi Minh City University of Technology and Education.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study assessed the comprehensive assessment of flexural and fatigue strength of the three-dimensional (3D)-printed polylactic acid (PLA) samples across diverse printing designs and parameters. The experiment framework included a diverse array of printing parameters: layer heights, first layer thicknesses, infill densities, top/bottom infill patterns, extruder temperatures, perimeters, and types of solid layer top and bottom. Our findings suggest that there is an interplay between these parameters and the mechanical properties of PLA specimens. Notably, the fatigue strength of PLA printing specimens is more significantly influenced (0.44%) by an increase in the thickness of the first layer compared to flexural strength (87%). The rate of increase in bending strength is lower in cases of layer height (3.55%) and initial layer height (0.44%) in contrast with other factors. Specimens with an initial layer thickness of 0.4 mm reached the highest number of cycles until failure, recording 21 022 cycles. Furthermore, the study identifies the infill pattern’s impact on strength, highlighting that the line infill pattern type case has the highest bending strength of 75.97 MPa and surpasses the honeycomb pattern in bending strength. Compared to the Honeycomb pattern, the rectilinear design has 2.1% higher bending strength. The number of cycles to failure of the rectilinear pattern is greater than those of the honeycomb pattern. In comparison to other patterns, the Rectilinear Top/Bottom infill pattern has a higher interest rate of 27.5% for bending strength and 200.83% for fatigue strength. Additionally, greater bending and flexural strength are obtained by raising the solid layer top, bottom, and perimeter values, respectively. In comparison to the other temperatures, the bending strength and fatigue strength are highest at 200 ° C. Therefore, the first layer height of 0.4 mm, the top/bottom rectilinear infill pattern, the extruder temperature of 200 ° C, the perimeter value of 3, the solid layer/top value of 3, and the solid layer/bottom value of 3 are the optimal values for the part subjected to at the same time bending strength combined with fatigue strength. This comprehensive study may provide a broader and deeper understanding of individual and combined effects on an overview of the bending and fatigue strength in connection to printing design and printing parameters, as well as the ideal optimal parameters for 3D printing with the PLA material. Manufacturers and designers can use the recommended parameters to optimize the strength of their printed parts, considering both bending and fatigue performance.

Förderung

  • Ho Chi Minh City University of Technology and Education

Zitieren

APA

Minh, P. S., Nguyen, V., Uyen, T. M. T., Do, T. T., Van, A. D. T., & Dang, H. N. L. (2024). The effects of 3D printing designs on PLA polymer flexural and fatigue strength. Journal of Micromechanics and Microengineering, 34(6), 065004. https://doi.org/10.1088/1361-6439/ad4b2a

Vancouver

Minh PS, Nguyen V, Uyen TMT, Do TT, Van ADT, Dang HNL. The effects of 3D printing designs on PLA polymer flexural and fatigue strength. Journal of Micromechanics and Microengineering. 2024;34(6):065004. doi:10.1088/1361-6439/ad4b2a

BibTeX
@article{Minh2024,
  author = {Minh, Pham Son and Nguyen, Van-Thuc and Uyen, Tran Minh The and Do, Thanh Trung and Van, Anh Duong Thi and Dang, Hai Nguyen Le},
  title = {The effects of 3D printing designs on PLA polymer flexural and fatigue strength},
  journal = {Journal of Micromechanics and Microengineering},
  year = {2024},
  volume = {34},
  number = {6},
  pages = {065004},
  doi = {10.1088/1361-6439/ad4b2a}
}
Kostenlos starten →