EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Threading-the-Needle: Compatibilization of HDPE/ i PP blends with butadiene-derived polyolefin block copolymers

Liyang Shen iD, Gabriela Diaz Gorbea iD, Evan Danielson iD, Shuquan Cui iD, Christopher J Ellison iD, Frank S Bates iD

Proceedings of the National Academy of Sciences · 22.08.2023 · 120 (34)

DOI: 10.1073/pnas.2301352120 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Proceedings of the National Academy of Sciences, online erschienen am 14.08.2023. Verfasst von Liyang Shen und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemical Engineering and Materials Science, University of Minnesota, Minneapolis, MN 55455. Die Arbeit wurde bisher 68-mal zitiert (Crossref) und nennt 56 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: National Science Foundation (NSF).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Management of the plastic industry is a momentous challenge, one that pits enormous societal benefits against an accumulating reservoir of nearly indestructible waste. A promising strategy for recycling polyethylene (PE) and isotactic polypropylene ( i PP), constituting roughly half the plastic produced annually worldwide, is melt blending for reformulation into useful products. Unfortunately, such blends are generally brittle and useless due to phase separation and mechanically weak domain interfaces. Recent studies have shown that addition of small amounts of semicrystalline PE- i PP block copolymers (ca. 1 wt%) to mixtures of these polyolefins results in ductility comparable to the pure materials. However, current methods for producing such additives rely on expensive reagents, prohibitively impacting the cost of recycling these inexpensive commodity plastics. Here, we describe an alternative strategy that exploits anionic polymerization of butadiene into block copolymers, with subsequent catalytic hydrogenation, yielding E and X blocks that are individually melt miscible with PE and i PP, where E and X are poly(ethylene- ran -ethylethylene) random copolymers with 6 wt% and 90 wt% ethylethylene repeat units, respectively. Cooling melt blended mixtures of PE and i PP containing 1 wt% of the triblock copolymer EXE of appropriate molecular weight, results in mechanical properties competitive with the component plastics. Blend toughness is obtained through interfacial topological entanglements of the amorphous X polymer and semicrystalline i PP, along with anchoring of the E blocks through cocrystallization with the PE homopolymer. Significantly, EXE can be inexpensively produced using currently practiced industrial scale polymerization methods, offering a practical approach to recycling the world’s top two plastics.

Schlagwörter

Stichwörter der Autor:innen

block copolymerpolyolefinrecycling

Autor:innen und Institutionen

  • Department of Chemical Engineering and Materials Science, University of Minnesota, Minneapolis, MN 55455.
  • Department of Chemistry, University of Minnesota, Minneapolis, MN 55455.

ORCID-Profile: Liyang Shen, Gabriela Diaz Gorbea, Evan Danielson, Shuquan Cui, Christopher J Ellison, Frank S Bates

Förderung

  • National Science Foundation (NSF)

Zitieren

APA

Shen, L., Gorbea, G. D., Danielson, E., Cui, S., Ellison, C. J., & Bates, F. S. (2023). Threading-the-Needle: Compatibilization of HDPE/ i PP blends with butadiene-derived polyolefin block copolymers. Proceedings of the National Academy of Sciences, 120(34). https://doi.org/10.1073/pnas.2301352120

Vancouver

Shen L, Gorbea GD, Danielson E, Cui S, Ellison CJ, Bates FS. Threading-the-Needle: Compatibilization of HDPE/ i PP blends with butadiene-derived polyolefin block copolymers. Proceedings of the National Academy of Sciences. 2023;120(34). doi:10.1073/pnas.2301352120

BibTeX
@article{Shen2023,
  author = {Shen, Liyang and Gorbea, Gabriela Diaz and Danielson, Evan and Cui, Shuquan and Ellison, Christopher J and Bates, Frank S},
  title = {Threading-the-Needle: Compatibilization of HDPE/ i PP blends with butadiene-derived polyolefin block copolymers},
  journal = {Proceedings of the National Academy of Sciences},
  year = {2023},
  volume = {120},
  number = {34},
  doi = {10.1073/pnas.2301352120}
}
Kostenlos starten →