EUVIMEDEUVIMED entdecken
Crossref

Detwinning deformation behaviors in Fe-Co-Ni-Al-Ti multi-component alloys

Wei-Bing Liao, Jiawei Zhang, Hongquan Song, Zhou Guan, Chuangshi Feng, Fuxiang Zhang

Applied Physics Letters · 16.03.2026 · 128 (11)

DOI: 10.1063/5.0320474 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Applied Physics Letters, online erschienen am 19.03.2026. Verfasst von Wei-Bing Liao und 5 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 42 Literaturangaben. Gefördert von: Basic and Applied Basic Research Foundation of Guangdong Province, Natural Science Foundation of Shenzhen Municipality, National Natural Science Foundation of China.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

FeCoNi-based multi-component alloys have great potential for engineering applications due to their excellent mechanical properties. In this study, (FeCoNi)95(AlTi)5 and (FeCoNi)90(AlTi)10 alloys (named AT5 and AT10) were prepared by vacuum arc melting and then homogenized, cold-rolled, and recrystallized in sequence. It was found that the AT5 alloy had a single FCC phase, while the AT10 contained an FCC matrix, and L12 precipitates with a grain size of ∼4.6 nm and a volume fraction of ∼17.3%. The microstructural evolution and deformation behaviors at different deformation stages were systematically studied by in situ tensile electron backscatter diffraction. Results showed that the AT5 alloy has a yield strength of 231 MPa and a ductility of 55.4%, whereas the AT10 alloy reaches 327 MPa and 34.5%. The AT5 alloy deformed by dislocation planar slip, in contrast to the wavy slip in the AT10 alloy. The increased large-sized atoms in AT10 alloy caused significant lattice distortion and solid solution strengthening, which increased the dislocation density and enhanced strain hardening capacity. However, the solute drag and nano-precipitates led to inhomogeneous deformation within grains, promoting void formation and premature failure. Both alloys showed a strain-induced detwinning behavior at different deformation stages. Despite a lower stacking fault energy in the AT10 alloy, its annealed twin content was reduced due to the nano-precipitates and solute drag. This in situ study provides real-time and compelling insights into the deformation mechanisms of high-performance multi-component alloys.

Förderung

  • Basic and Applied Basic Research Foundation of Guangdong Province
  • Natural Science Foundation of Shenzhen Municipality
  • National Natural Science Foundation of China

Zitieren

APA

Liao, W., Zhang, J., Song, H., Guan, Z., Feng, C., & Zhang, F. (2026). Detwinning deformation behaviors in Fe-Co-Ni-Al-Ti multi-component alloys. Applied Physics Letters, 128(11). https://doi.org/10.1063/5.0320474

Vancouver

Liao W, Zhang J, Song H, Guan Z, Feng C, Zhang F. Detwinning deformation behaviors in Fe-Co-Ni-Al-Ti multi-component alloys. Applied Physics Letters. 2026;128(11). doi:10.1063/5.0320474

BibTeX
@article{Liao2026,
  author = {Liao, Wei-Bing and Zhang, Jiawei and Song, Hongquan and Guan, Zhou and Feng, Chuangshi and Zhang, Fuxiang},
  title = {Detwinning deformation behaviors in Fe-Co-Ni-Al-Ti multi-component alloys},
  journal = {Applied Physics Letters},
  year = {2026},
  volume = {128},
  number = {11},
  doi = {10.1063/5.0320474}
}
Kostenlos starten →