EUVIMEDEUVIMED entdecken
Crossref

Development of Cu–In–Ga–S quantum dots with a narrow emission peak for red electroluminescence

Chang Jiang iD, Makoto Tozawa iD, Kazutaka Akiyoshi iD, Tatsuya Kameyama iD, Takahisa Yamamoto iD, Genichi Motomura iD, Yoshihide Fujisaki, Taro Uematsu iD, Susumu Kuwabata, Tsukasa Torimoto iD

The Journal of Chemical Physics · 28.04.2023 · 158 (16)

DOI: 10.1063/5.0144271 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Chemical Physics, online erschienen am 25.04.2023. Verfasst von Chang Jiang und 9 weiteren Autor:innen. Beteiligte Einrichtung: Graduate School of Engineering, Nagoya University, Chikusa-ku, Nagoya 464-8603, Japan. Die Arbeit wurde bisher 23-mal zitiert (Crossref) und nennt 56 Literaturangaben. Gefördert von: Japan Society for the Promotion of Science.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Narrowing the emission peak width and adjusting the peak position play a key role in the chromaticity and color accuracy of display devices with the use of quantum dot light-emitting diodes (QD-LEDs). In this study, we developed multinary Cu–In–Ga–S (CIGS) QDs showing a narrow photoluminescence (PL) peak by controlling the Cu fraction, i.e., Cu/(In+Ga), and the ratio of In to Ga composing the QDs. The energy gap of CIGS QDs was enlarged from 1.74 to 2.77 eV with a decrease in the In/(In+Ga) ratio from 1.0 to 0. The PL intensity was remarkably dependent on the Cu fraction, and the PL peak width was dependent on the In/(In+Ga) ratio. The sharpest PL peak at 668 nm with a full width at half maximum (fwhm) of 0.23 eV was obtained for CIGS QDs prepared with ratios of Cu/(In+Ga) = 0.3 and In/(In+Ga) = 0.7, being much narrower than those previously reported with CIGS QDs, fwhm of >0.4 eV. The PL quantum yield of CIGS QDs, 8.3%, was increased to 27% and 46% without a PL peak broadening by surface coating with GaSx and Ga–Zn–S shells, respectively. Considering a large Stokes shift of >0.5 eV and the predominant PL decay component of ∼200–400 ns, the narrow PL peak was assignable to the emission from intragap states. QD-LEDs fabricated with CIGS QDs surface-coated with GaSx shells showed a red color with a narrow emission peak at 688 nm with a fwhm of 0.24 eV.

Autor:innen und Institutionen

  • Graduate School of Engineering, Nagoya University, Chikusa-ku, Nagoya 464-8603, Japan.
  • Science and Technology Research Laboratories, Japan Broadcasting Corporation (NHK), Setagaya-ku, Tokyo 157-8510, Japan.
  • Department of Applied Chemistry, Graduate School of Engineering, Osaka University, Suita, Osaka 565-0871, Japan.
  • Innovative Catalysis Science Division, Institute for Open and Transdisciplinary Research Initiatives (ICS-OTRI), Osaka University, Suita, Osaka 565-0871, Japan.

ORCID-Profile: Chang Jiang, Makoto Tozawa, Kazutaka Akiyoshi, Tatsuya Kameyama, Takahisa Yamamoto, Genichi Motomura, Taro Uematsu, Tsukasa Torimoto

Förderung

  • Japan Society for the Promotion of Science

Zitieren

APA

Jiang, C., Tozawa, M., Akiyoshi, K., Kameyama, T., Yamamoto, T., Motomura, G., Fujisaki, Y., Uematsu, T., Kuwabata, S., & Torimoto, T. (2023). Development of Cu–In–Ga–S quantum dots with a narrow emission peak for red electroluminescence. The Journal of Chemical Physics, 158(16). https://doi.org/10.1063/5.0144271

Vancouver

Jiang C, Tozawa M, Akiyoshi K, Kameyama T, Yamamoto T, Motomura G, et al. Development of Cu–In–Ga–S quantum dots with a narrow emission peak for red electroluminescence. The Journal of Chemical Physics. 2023;158(16). doi:10.1063/5.0144271

BibTeX
@article{Jiang2023,
  author = {Jiang, Chang and Tozawa, Makoto and Akiyoshi, Kazutaka and Kameyama, Tatsuya and Yamamoto, Takahisa and Motomura, Genichi and Fujisaki, Yoshihide and Uematsu, Taro and Kuwabata, Susumu and Torimoto, Tsukasa},
  title = {Development of Cu–In–Ga–S quantum dots with a narrow emission peak for red electroluminescence},
  journal = {The Journal of Chemical Physics},
  year = {2023},
  volume = {158},
  number = {16},
  doi = {10.1063/5.0144271}
}
Kostenlos starten →