EUVIMEDEUVIMED entdecken
Crossref

Innovations in Microsurgery: A Qualitative Appraisal of a Novel 3D-Printed Microscope

Emily E Zona, Sahand C Eftekari, Elizabeth P Wu, Myiah P Quach, M Kristine Carbullido, Ellen C Via, Weifeng Zeng iD, Aaron M Dingle iD, Samuel O Poore iD

Journal of Reconstructive Microsurgery · 15.10.2026

DOI: 10.1055/a-2972-6217 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Reconstructive Microsurgery, erschienen am 15.10.2026. Verfasst von Emily E Zona und 8 weiteren Autor:innen. Beteiligte Einrichtung: University of Wisconsin School of Medicine and Public Health, Department of Surgery, Wisconsin, United States, Madison. Die Arbeit nennt 6 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Microsurgery is a critical component of plastic and reconstructive surgery. However, the high cost of training and equipment poses significant barriers, particularly in resource-limited settings. To address this challenge, the Microsurgery and Regenerative Medicine Laboratory within the Division of Plastic Surgery at the University of Wisconsin developed a low-cost, three-dimensionally (3D)-printed surgical microscope. This study qualitatively appraised the use of this novel microscope for microsurgery training by surveying surgeons about their experiences using this tool relative to traditional magnification methods. In this prospective, multi-institutional appraisal study, surgical residents, fellows, and attending surgeons with varying microsurgical experience performed a single end-to-end microsurgical anastomosis on chicken thigh femoral arteries using the 3D-printed microscope. Participants then completed a survey assessing ease of use, adequacy for microsurgical training, educational value, and perceived impact on teaching capacity in local and global settings. Over 80% of participants (Survey 1: n = 36; Survey 2: n = 24) reported that performing an end-to-end anastomosis was easier or equivalent using the 3D-printed microscope compared with surgical loupes. All respondents expressed willingness to use the device for microsurgery teaching and practice. Additionally, 91.7% (33/36) believed access to the microscope would enhance microsurgical teaching at their home institutions, and 97.1% (34/35) felt it would improve teaching capacity globally. Qualitative feedback was overwhelmingly positive, with suggestions primarily related to ergonomics and lighting. This study supports that this low-cost, 3D-printed microscope is an effective microsurgical training tool. Ongoing design refinements informed by user feedback may further optimize its role in expanding access to microsurgery education worldwide.

Autor:innen und Institutionen

  • University of Wisconsin School of Medicine and Public Health, Department of Surgery, Wisconsin, United States, Madison.
  • Mayo Clinic College of Medicine and Science, Minnesota, United States, Rochester.

ORCID-Profile: Weifeng Zeng, Aaron M Dingle, Samuel O Poore

Zitieren

APA

Zona, E. E., Eftekari, S. C., Wu, E. P., Quach, M. P., Carbullido, M. K., Via, E. C., Zeng, W., Dingle, A. M., & Poore, S. O. (2026). Innovations in Microsurgery: A Qualitative Appraisal of a Novel 3D-Printed Microscope. Journal of Reconstructive Microsurgery. https://doi.org/10.1055/a-2972-6217

Vancouver

Zona EE, Eftekari SC, Wu EP, Quach MP, Carbullido MK, Via EC, et al. Innovations in Microsurgery: A Qualitative Appraisal of a Novel 3D-Printed Microscope. Journal of Reconstructive Microsurgery. 2026. doi:10.1055/a-2972-6217

BibTeX
@article{Zona2026,
  author = {Zona, Emily E and Eftekari, Sahand C and Wu, Elizabeth P and Quach, Myiah P and Carbullido, M Kristine and Via, Ellen C and Zeng, Weifeng and Dingle, Aaron M and Poore, Samuel O},
  title = {Innovations in Microsurgery: A Qualitative Appraisal of a Novel 3D-Printed Microscope},
  journal = {Journal of Reconstructive Microsurgery},
  year = {2026},
  doi = {10.1055/a-2972-6217}
}
Kostenlos starten →