EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Maxillary and Mandibular Reconstruction Using VSP and 3D Printing Technology: A Review of 42 Patients

Konstantinos Benetatos, Konstantinos S. Papadopoulos, Vasileios A. Kontogeorgakos, Olga D. Savvidou, Panayiotis J. Papagelopoulos

Journal of Reconstructive Microsurgery Open · 01.07.2026 · 11 (02) · e81-e86

DOI: 10.1055/a-2960-1519 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Reconstructive Microsurgery Open, erschienen am 01.07.2026. Verfasst von Konstantinos Benetatos und 4 weiteren Autor:innen. Die Arbeit nennt 19 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

Accuracy of the reconstructed bony structures is key to achieving favorable aesthetic and functional results in head and neck reconstruction. For precision in preoperative planning in oncological resections, trauma, composite flap harvesting, and reconstruction, we applied three-dimensional (3D) printing technology.

Methods

About 42 patients were treated (25 males and 17 females) over 6 years by a single surgeon. Of these, 34 had neoplasia, and 8 had trauma. About 40 fibula flaps and 2 DCIA were used. Each patient underwent a computed tomography (CT) scan following an appropriate scanning protocol. The image data (Digital Imaging and Communications in Medicine [DICOM]) were converted to a 3D virtual model using appropriate medical software (MIMICS and BLENDER), and the resection and reconstruction surgery were virtually performed. Cutting guides for both donor and recipient sites were printed. The reconstructed maxilla/mandible with the bony flap was also printed to prebend the reconstruction plate.

Results

The flap success rate was 97.6%. Two flaps appeared with venous congestion, but both were salvaged after urgent reexploration in the operating room. There was one (2.4%) flap loss. There were two (7.4%) donor site hematomas and one (3.4%) orocutaneous fistula of the neck. Flap warm ischemia time was significantly reduced, and accuracy in bony reconstruction was achieved. Dental implants were successfully placed in 29 patients.

Conclusion

The process of 3D printing allowed accurate flap fabrication in situ (osteotomies), prior to division of the pedicle, thereby minimizing warm ischemia time, allowing accurate fixation of the composite flap, maintaining the condyles in place, and achieving accurate occlusion.

Zitieren

APA

Benetatos, K., Papadopoulos, K. S., Kontogeorgakos, V. A., Savvidou, O. D., & Papagelopoulos, P. J. (2026). Maxillary and Mandibular Reconstruction Using VSP and 3D Printing Technology: A Review of 42 Patients. Journal of Reconstructive Microsurgery Open, 11(02), e81-e86. https://doi.org/10.1055/a-2960-1519

Vancouver

Benetatos K, Papadopoulos KS, Kontogeorgakos VA, Savvidou OD, Papagelopoulos PJ. Maxillary and Mandibular Reconstruction Using VSP and 3D Printing Technology: A Review of 42 Patients. Journal of Reconstructive Microsurgery Open. 2026;11(02):e81-e86. doi:10.1055/a-2960-1519

BibTeX
@article{Benetatos2026,
  author = {Benetatos, Konstantinos and Papadopoulos, Konstantinos S. and Kontogeorgakos, Vasileios A. and Savvidou, Olga D. and Papagelopoulos, Panayiotis J.},
  title = {Maxillary and Mandibular Reconstruction Using VSP and 3D Printing Technology: A Review of 42 Patients},
  journal = {Journal of Reconstructive Microsurgery Open},
  year = {2026},
  volume = {11},
  number = {02},
  pages = {e81--e86},
  doi = {10.1055/a-2960-1519}
}
Kostenlos starten →