Investigation on microstructural evolution and surface integrity of Ti-6Al-4V alloy machined using WC nanoparticle-enhanced powder-suspended EDM
Metallurgical Research & Technology · 2026 · 123 (1) · 115
DOI: 10.1051/metal/2025108 ↗Kurz gefasst
Fachartikel in der Zeitschrift Metallurgical Research & Technology, online erschienen am 09.01.2026. Verfasst von Elaiyarasan Uthirapathi und 4 weiteren Autor:innen. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 47 Literaturangaben.
Abstract (Originalsprache)
Ti-6Al-4V paly crucial role in biomedical, automobile, and aerospace sectors; however, its high chemical reactivity and low thermal conductivity poses serious challenges during traditional machining. Electrical discharge machining (EDM) has demonstrated significant potential in improving surface characteristics; however, the integration of powder-suspended EDM (PS-EDM) further enhances machining performance. This study investigates the effects of tungsten carbide (WC) nanoparticle-enriched dielectric fluid on the material removal rate (MRR), microhardness (MH), surface roughness (SR), and microstructural characteristics of Ti-6Al-4V alloy. WC nanoparticles were introduced into the dielectric fluid at varying concentration of 0, 1, 3 and 5 g/L, with continuous mechanical stirring. The controlled EDM parameters included discharge current (I) of 4 A, 6 A, 8 A and pulse on time (T on ) of 30 μs, 50 μs, 70 μs. The results revealed that an optimal WC concentration of 3 g/L, coupled with increasing ‘I’ and ‘T on ’, led to enhanced MRR, MH, while reducing SR. The maximum MRR (0.0223 g/min) and MH (515 HV) were achieved at 3 g/L, 8 A, 70 μs, whereas the lowest SR (2.85 μm) was observed at 3 g/L, 6 A, 50 μs. MH improved by 63.4% compared to the base alloy. Scanning electron microscope (SEM) analysis confirmed a refined surface with minimal defects at 6 A, 50 μs, 3 g/L, whereas deep crater, and nanoparticle agglomeration were evident at 8A, 70 μs, and 5 g/L. This study establishes that WC concentration, ‘I’ and ‘T on ’ significantly influence machining performance and surface integrity during EDM of Ti-6Al-4V alloy. Future research could explore the dispersion of hybrid nanoparticle in bio-based dielectric fluids to optimize machining efficiency and surface characteristics.
Zitieren
APA
Uthirapathi, E., Ganesan, S. K., Arjunan, V., Theerthamalai, E., & Teja, P. V. S. (2026). Investigation on microstructural evolution and surface integrity of Ti-6Al-4V alloy machined using WC nanoparticle-enhanced powder-suspended EDM. Metallurgical Research & Technology, 123(1), 115. https://doi.org/10.1051/metal/2025108
Vancouver
Uthirapathi E, Ganesan SK, Arjunan V, Theerthamalai E, Teja PVS. Investigation on microstructural evolution and surface integrity of Ti-6Al-4V alloy machined using WC nanoparticle-enhanced powder-suspended EDM. Metallurgical Research & Technology. 2026;123(1):115. doi:10.1051/metal/2025108
BibTeX
@article{Uthirapathi2026,
author = {Uthirapathi, Elaiyarasan and Ganesan, Shanthos Kumar and Arjunan, Visagan and Theerthamalai, Elangovan and Teja, Putti Venkata Siva},
title = {Investigation on microstructural evolution and surface integrity of Ti-6Al-4V alloy machined using WC nanoparticle-enhanced powder-suspended EDM},
journal = {Metallurgical Research & Technology},
year = {2026},
volume = {123},
number = {1},
pages = {115},
doi = {10.1051/metal/2025108}
}
EUVIMED