EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A dual-crosslinking electroactive hydrogel based on gelatin methacrylate and dibenzaldehyde-terminated telechelic polyethylene glycol for 3D bio-printing

Yulong Wang, Songsong Yang, Heqing Cai, Hailong Hu, Kun Hu, Zhicheng Sun, Ruping Liu, Yen Wei, Lu Han

Scientific Reports · 2024

DOI: 10.1038/s41598-024-54853-9 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Scientific Reports, 2024. Verfasst von Yulong Wang und 8 weiteren Autor:innen. Beteiligte Einrichtung: The Engineering Research Center of 3D Printing and Bio-Fabrication, Beijing Institute of Graphic Communication, Beijing, 102600, China. Hauptthemen laut MEDLINE: Nanotubes, Carbon, Bioprinting. Die Arbeit wurde bisher 23-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key Research and Development Program of China, the International Cooperation and Exchanges Program of the National Natural Science Foundation of China, the National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Gelatin was widely used as scaffold materials in 3D bio-printing due to its excellent bioactivity and availability and especially that their arginine–glycine–aspartic acid (RGD) sequences could efficiently promote cell adhesion and proliferation. In this study, an electroactive and 3D bio-printable hydrogel was prepared through a two-step chemical cross-linking process. Specifically, residual free amino groups of methacrylated gelatin (GelMA) were cross-linked with the aldehyde groups of dibenzaldehyde-terminated telechelic polyethylene glycol (DF-PEG) via Schiff base bonds, forming a gel at 37 °C. During the subsequent 3D bio-printing process, GelMA underwent UV curing, forming a secondary cross-linked network to the mechanical strength and stability of the printed structure. The uniform dispersion of carbon nanotubes (CNTs) in the GelMA/DF-PEG composite hydrogel significantly increased its conductivity. The optimized GelMA/DF-PEG composite hydrogel, i.e., 30% GelMA and 25% DF-PEG (G30D25-CNTs), exhibited superior bio-printability. When the content of CNTs was above 4%, the conductivity of G30D25-CNTs hydrogel exceeded 10 –2 S/m, which satisfied the needs of cells for micro-current stimulation. Furthermore, the pore microstructures, swelling behavior, degradation ability and cell toxicity of G30D25-CNTs electroactive hydrogels were thoroughly evaluated. Thus, the G30D25-CNTs hydrogel with 4% MWCNTs could be considered for further application in electrical stimulation of tissue regeneration such as muscle and cardiac nerve tissue repair.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Nanotubes, CarbonBioprintingGelatinPolyethylene GlycolsHydrogelsMethacrylatesBiocompatible MaterialsPrinting, Three-DimensionalTissue EngineeringTissue Scaffolds

Substanzen

GelatinPolyethylene GlycolsNanotubes, CarbonHydrogelsMethacrylatesBiocompatible Materials

Autor:innen und Institutionen

  • The Engineering Research Center of 3D Printing and Bio-Fabrication, Beijing Institute of Graphic Communication, Beijing, 102600, China.
  • School of Physical Science and Technology, Guangxi University, Nanning, 530004, China.
  • The Engineering Research Center of 3D Printing and Bio-Fabrication, Beijing Institute of Graphic Communication, Beijing, 102600, China. weiyen@tsinghua.edu.cn.
  • The Key Laboratory of Bioorganic Phosphorus Chemistry and Chemical Biology (Ministry of Education), Department of Chemistry, Tsinghua University, Beijing, 100084, China. weiyen@tsinghua.edu.cn.
  • The Engineering Research Center of 3D Printing and Bio-Fabrication, Beijing Institute of Graphic Communication, Beijing, 102600, China. hanlu@iccas.ac.cn.

Förderung

  • National Key Research and Development Program of China
  • the International Cooperation and Exchanges Program of the National Natural Science Foundation of China
  • the National Natural Science Foundation of China
  • Scientific Research Innovation Project from Beijing Institute of Graphic Communication

Zitieren

APA

Wang, Y., Yang, S., Cai, H., Hu, H., Hu, K., Sun, Z., Liu, R., Wei, Y., & Han, L. (2024). A dual-crosslinking electroactive hydrogel based on gelatin methacrylate and dibenzaldehyde-terminated telechelic polyethylene glycol for 3D bio-printing. Scientific Reports. https://doi.org/10.1038/s41598-024-54853-9

Vancouver

Wang Y, Yang S, Cai H, Hu H, Hu K, Sun Z, et al. A dual-crosslinking electroactive hydrogel based on gelatin methacrylate and dibenzaldehyde-terminated telechelic polyethylene glycol for 3D bio-printing. Scientific Reports. 2024. doi:10.1038/s41598-024-54853-9

BibTeX
@article{Wang2024,
  author = {Wang, Yulong and Yang, Songsong and Cai, Heqing and Hu, Hailong and Hu, Kun and Sun, Zhicheng and Liu, Ruping and Wei, Yen and Han, Lu},
  title = {A dual-crosslinking electroactive hydrogel based on gelatin methacrylate and dibenzaldehyde-terminated telechelic polyethylene glycol for 3D bio-printing},
  journal = {Scientific Reports},
  year = {2024},
  doi = {10.1038/s41598-024-54853-9}
}
Kostenlos starten →