EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Assessing the Environmental Impacts of Microfluidic Devices for Glucose Detection

Kristie J Tjokro iD, Valerio Barbarossa, Stefano Cucurachi, Alina Rwei iD, Justin Lian

ACS Sustainable Chemistry & Engineering · 30.06.2025 · 13 (25) · 9500-9509

DOI: 10.1021/acssuschemeng.5c01511 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Sustainable Chemistry & Engineering, online erschienen am 18.06.2025. Verfasst von Kristie J Tjokro und 4 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Environmental Sciences (CML), Leiden University, Einsteinweg 2, Leiden 2333 CC, The Netherlands. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 72 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Commission.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Healthcare must balance safety, efficiency, and effectiveness with affordability and accessibility. Microfluidic devices offer low-cost, portable solutions for point-of-care testing, miniaturizing lab functions on chips through microchannels for quick diagnostics, retaining resolution and sensitivity with minimal reagent use. However, their environmental sustainability is uncertain, with concerns about production scale-up, risks from disposability, and the impact of alternative raw materials or manufacturing techniques compared to traditional soft lithography based on polydimethylsiloxane (PDMS). We conducted a cradle-to-grave life-cycle assessment (LCA) of three glucose-detection devices, a PDMS device via soft lithography, a paper device via wax stamping, and a polylactic acid (PLA) device via 3D printing, for both laboratory-scale and commercial-scale production. For lab-scale production, the paper device had the lowest environmental impact across most impact categories, while the PLA device had the highest. However, for commercial-scale production, by transitioning from 3D printing to injection molding, the PLA device performed best overall, while PDMS performed the worst. For both scales, material and energy use were key contributors, with minimal impact from the use phase. This study highlights the importance of considering environmental impacts at multiple scales and shows the added value of using LCA to guide design and production for early-stage technologies.

Schlagwörter

Stichwörter der Autor:innen

3D printingemerging technologiesex antelab-on-a-chippolydimethylsiloxanepolylactic acidprocess scale-uprapid prototyping

Autor:innen und Institutionen

  • Institute of Environmental Sciences (CML), Leiden University, Einsteinweg 2, Leiden 2333 CC, The Netherlands.
  • Global Sustainability, PBL Netherlands Environmental Assessment Agency, Bezuidenhoutseweg 30, The Hague 2500 GH, The Netherlands.
  • Department of Chemical Engineering, Delft University of Technology, Van der Maasweg 9, Delft 2629 HZ, The Netherlands.

ORCID-Profile: Kristie J Tjokro, Alina Rwei

Förderung

  • European Commission

Zitieren

APA

Tjokro, K. J., Barbarossa, V., Cucurachi, S., Rwei, A., & Lian, J. (2025). Assessing the Environmental Impacts of Microfluidic Devices for Glucose Detection. ACS Sustainable Chemistry & Engineering, 13(25), 9500-9509. https://doi.org/10.1021/acssuschemeng.5c01511

Vancouver

Tjokro KJ, Barbarossa V, Cucurachi S, Rwei A, Lian J. Assessing the Environmental Impacts of Microfluidic Devices for Glucose Detection. ACS Sustainable Chemistry & Engineering. 2025;13(25):9500-9509. doi:10.1021/acssuschemeng.5c01511

BibTeX
@article{Tjokro2025,
  author = {Tjokro, Kristie J and Barbarossa, Valerio and Cucurachi, Stefano and Rwei, Alina and Lian, Justin},
  title = {Assessing the Environmental Impacts of Microfluidic Devices for Glucose Detection},
  journal = {ACS Sustainable Chemistry & Engineering},
  year = {2025},
  volume = {13},
  number = {25},
  pages = {9500--9509},
  doi = {10.1021/acssuschemeng.5c01511}
}
Kostenlos starten →