EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Effect of the Applied Pressure on the Physical and Chemical Properties of Nickel Films Prepared by Electroless Plating on Beech Wood

Jamal Amer iD

ACS Omega · 10.11.2026 · 11 (44) · 69003-69012

DOI: 10.1021/acsomega.6c08879 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Omega, online erschienen am 29.10.2026. Verfasst von Jamal Amer. Beteiligte Einrichtung: Department of Chemistry, Atomic Energy Commission of Syria, 17 Nissan Street, P.O. Box 6091, Damascus, Syrian Arab Republic. Die Arbeit nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Atomic Energy Commission of Syria.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Nickel films were deposited on beech wood substrates using the electroless plating method, and the effect of applied mechanical pressures (2, 4, 6, and 8 kN/cm2) on their structural, morphological, wetting, and electrical properties was systematically investigated. Nickel-coated wood specimens were subjected to uniaxial pressures for 3 s, followed by characterization using scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), X-ray diffraction (XRD), contact-angle (CA) measurements, and current–voltage (I–V) analysis. SEM revealed surface openings of approximately 2–4 μm at 2 kN/cm2, which progressively narrowed with increasing pressure and were nearly absent at 8 kN/cm2. Cross-sectional SEM-EDS confirmed Ni penetration into the porous wood structure, with the greatest apparent penetration depth observed at 6 kN/cm2. XRD identified face-centered-cubic Ni with a preferential (111) orientation, while Williamson-Hall analysis indicated pressure-dependent variations in crystallite size and lattice microstrain. The wetting behavior exhibited a pressure-dependent response, with the highest initial contact angle observed at 6 kN/cm2, followed by a decrease at 8 kN/cm2 consistent with increased water penetration associated with pressure-induced surface and interfacial damage. All samples exhibited approximately linear I–V characteristics (R2 > 0.99), with the highest electrical response observed at 6 kN/cm2 and a subsequent decline at 8 kN/cm2. Overall, the results demonstrate a pressure-dependent balance between compaction of the nickel conductive network at moderate pressures and mechanical degradation under excessive compression, providing a basis for pressure-controlled design of functional conductive Ni/wood interfaces.

Autor:innen und Institutionen

  • Department of Chemistry, Atomic Energy Commission of Syria, 17 Nissan Street, P.O. Box 6091, Damascus, Syrian Arab Republic.

ORCID-Profile: Jamal Amer

Förderung

  • Atomic Energy Commission of Syria

Zitieren

APA

Amer, J. (2026). Effect of the Applied Pressure on the Physical and Chemical Properties of Nickel Films Prepared by Electroless Plating on Beech Wood. ACS Omega, 11(44), 69003-69012. https://doi.org/10.1021/acsomega.6c08879

Vancouver

Amer J. Effect of the Applied Pressure on the Physical and Chemical Properties of Nickel Films Prepared by Electroless Plating on Beech Wood. ACS Omega. 2026;11(44):69003-69012. doi:10.1021/acsomega.6c08879

BibTeX
@article{Amer2026,
  author = {Amer, Jamal},
  title = {Effect of the Applied Pressure on the Physical and Chemical Properties of Nickel Films Prepared by Electroless Plating on Beech Wood},
  journal = {ACS Omega},
  year = {2026},
  volume = {11},
  number = {44},
  pages = {69003--69012},
  doi = {10.1021/acsomega.6c08879}
}
Kostenlos starten →