Thrust Symmetry Engineering in Lithographically Defined Bubble-Propelled Micromotors via Multi-Orifice Exhaust-Port Design
ACS Omega · 18.08.2026 · 11 (32) · 48463-48471
DOI: 10.1021/acsomega.6c05214 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Omega, online erschienen am 01.08.2026. Verfasst von Isao Shitanda und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Pure and Applied Chemistry, Faculty of Science and Technology, Tokyo University of Science, 2641, Yamazaki, Noda, Chiba 278-8510, Japan. Die Arbeit nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Bubble-driven catalytic micromotors generate thrust through gas–liquid interfacial processes at the inner surfaces of the catalyst; however, systematic control over the thrust-vector symmetry through the geometric design of the exhaust port layout has not been demonstrated. Here, we report a lithographic fabrication platform that produces stacked Au/Pt hollow micromotors with independently programmable catalytic exhaust-port configurations─single, two, and three orifices─which enable a direct experimental investigation of the extent to which the interface-defined port geometry strongly influences the propulsion behavior. Using a single-orifice trapezoidal micromotor as the baseline system, we establish concentration-dependent propulsion at 73 μm s–1 (5 wt % H2O2) and 636 μm s–1 (15 wt % H2O2). Extending the platform to a two-orifice design reveals persistent curved trajectories (∼450 μm s–1, 15 wt % H2O2), indicating that even small geometric asymmetries in exhaust-port placement can produce measurable and persistent torque. A three-orifice design incorporating a central forward-thrust port and two lateral steering ports enables the straight-line motion to be recovered under uniform fuel conditions, consistent with improved thrust-vector balance for the mirror-symmetric port placement. In a nonuniform fuel environment imposed by a H2O2 gel source, the three-orifice micromotor exhibits directional motion toward the low-concentration region, consistent with differential bubble generation across the lateral ports. These results establish that, within the present platform and under the same material and catalytic conditions, the number, placement, and symmetry of exhaust ports strongly affect the observed propulsion state, providing an interface-programmable geometric route to activate micromotor behavior without changing the material composition or fuel chemistry.
Autor:innen und Institutionen
- Department of Pure and Applied Chemistry, Faculty of Science and Technology, Tokyo University of Science, 2641, Yamazaki, Noda, Chiba 278-8510, Japan.
- Research Institute for Science and Technology, Tokyo University of Science, 2641 Yamazaki, Noda, Chiba 278-8510, Japan.
ORCID-Profile: Isao Shitanda, Yoshinao Hoshi, Masanori Hayase, Masayuki Itagaki
Zitieren
APA
Shitanda, I., Suzuki, T., Zama, K., Hoshi, Y., Hayase, M., & Itagaki, M. (2026). Thrust Symmetry Engineering in Lithographically Defined Bubble-Propelled Micromotors via Multi-Orifice Exhaust-Port Design. ACS Omega, 11(32), 48463-48471. https://doi.org/10.1021/acsomega.6c05214
Vancouver
Shitanda I, Suzuki T, Zama K, Hoshi Y, Hayase M, Itagaki M. Thrust Symmetry Engineering in Lithographically Defined Bubble-Propelled Micromotors via Multi-Orifice Exhaust-Port Design. ACS Omega. 2026;11(32):48463-48471. doi:10.1021/acsomega.6c05214
BibTeX
@article{Shitanda2026,
author = {Shitanda, Isao and Suzuki, Takuma and Zama, Kentaro and Hoshi, Yoshinao and Hayase, Masanori and Itagaki, Masayuki},
title = {Thrust Symmetry Engineering in Lithographically Defined Bubble-Propelled Micromotors via Multi-Orifice Exhaust-Port Design},
journal = {ACS Omega},
year = {2026},
volume = {11},
number = {32},
pages = {48463--48471},
doi = {10.1021/acsomega.6c05214}
}
EUVIMED