Improving Thermosensitive Bioink Scaffold Fabrication with a Temperature-Regulated Printhead in Robot-Assisted In Situ Bioprinting System
ACS Omega · 01.10.2024 · 9 (39) · 40618-40631
DOI: 10.1021/acsomega.4c04373 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Omega, online erschienen am 18.09.2024. Verfasst von Zitong Wang und 11 weiteren Autor:innen. Beteiligte Einrichtung: Department of Biomedical Engineering, School of Health Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093, C…. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: National Natural Science Foundation of China, China Postdoctoral Science Foundation, Science and Technology Commission of Shanghai Municipality.
Abstract (Originalsprache)
In situ bioprinting enables precise 3D printing inside the human body using modified bioprinters with thermosensitive bioinks such as gelatin methacrylate (GelMA). However, these devices lack refined temperature-regulated mechanisms essential for ensuring bioink viscosity, as compared to traditional bio-3D printers. Addressing this challenge, this study presents a temperature-regulated printhead designed to improve the fabrication of thermosensitive bioink scaffolds in in situ bioprinting, integrated into a UR5 robotic arm. Featuring a closed-loop system, it achieves a temperature steady error of 1 °C and a response time of approximately 1 min. The effectiveness of the printer was validated by bioprinting multilayer lattice 3D bioscaffolds. Comparisons were made with or without temperature control using different concentrations of GelMA + LAP. The deformation of the bioscaffolds under both conditions was analyzed, and cell culture tests were conducted to verify viability. Additionally, the rheology and mechanical properties of GelMA were tested. A final preliminary in situ bioprinting experiment was conducted on a model of a damaged femur to demonstrate practical application. The fabrication of this printhead is entirely open source, facilitating easy modifications to accommodate various robotic arms. We encourage readers to advance this prototype for application in increasingly complex in situ bioprinting situations, especially those utilizing thermosensitive bioinks.
Autor:innen und Institutionen
- Department of Biomedical Engineering, School of Health Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093, China.
- Shanghai Ninth People's Hospital, School of Medicine, Shanghai Jiao Tong University, Shanghai 200011, China.
- Department of Mechanical, School of Mechanical & Electrical Engineering, Henan University of Technology, Zhengzhou 450001, Henan Province, China.
- School of Pharmacy, Jiangsu Ocean University, Lianyungang 222005, Jiangsu Province, China.
- Institute of Biomedical Engineering, College of Medicine, Southwest Jiaotong University, Chengdu 611756, Sichuan Province, China.
- Innovative Medical Device Registration Research and Clinical Transformation Service Center, Institute of Translational Medicine, Shanghai Jiao Tong University, Shanghai 200240, China.
ORCID-Profile: Jinwu Wang
Förderung
- National Natural Science Foundation of China
- China Postdoctoral Science Foundation
- Science and Technology Commission of Shanghai Municipality
- Shanghai Jiao Tong University
- School of Medicine, Shanghai Jiao Tong University
- National Key Research and Development Program of China
- Jiangsu Provincial Key Research and Development Program
- Shanghai Municipality
Zitieren
APA
Wang, Z., Lin, L., Li, X., Zhang, Q., Mi, X., Xu, B., Xu, Y., Liu, T., Shen, Y., Wang, Z., Xie, N., & Wang, J. (2024). Improving Thermosensitive Bioink Scaffold Fabrication with a Temperature-Regulated Printhead in Robot-Assisted In Situ Bioprinting System. ACS Omega, 9(39), 40618-40631. https://doi.org/10.1021/acsomega.4c04373
Vancouver
Wang Z, Lin L, Li X, Zhang Q, Mi X, Xu B, et al. Improving Thermosensitive Bioink Scaffold Fabrication with a Temperature-Regulated Printhead in Robot-Assisted In Situ Bioprinting System. ACS Omega. 2024;9(39):40618-40631. doi:10.1021/acsomega.4c04373
BibTeX
@article{Wang2024,
author = {Wang, Zitong and Lin, Li and Li, Xiangyu and Zhang, Quan and Mi, Xuelian and Xu, Bide and Xu, Yuanjing and Liu, Tongyou and Shen, Yuling and Wang, Zan and Xie, Neng and Wang, Jinwu},
title = {Improving Thermosensitive Bioink Scaffold Fabrication with a Temperature-Regulated Printhead in Robot-Assisted In Situ Bioprinting System},
journal = {ACS Omega},
year = {2024},
volume = {9},
number = {39},
pages = {40618--40631},
doi = {10.1021/acsomega.4c04373}
}
EUVIMED