Cleaning Oil-Based Drilling Cuttings with Synthetic Gemini Surfactants
ACS Omega · 05.03.2024 · 9 (9) · 10488-10497
DOI: 10.1021/acsomega.3c08618 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Omega, online erschienen am 20.02.2024. Verfasst von Xuan Yan und 5 weiteren Autor:innen. Beteiligte Einrichtung: College of Chemistry and Chemical Engineering, Southwest Petroleum University, Chengdu 610500, Sichuan, P. R. China. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Sichuan Provincial Youth Science and Technology Foundation, Regional Innovation Cooperation project of Sichuan Province.
Abstract (Originalsprache)
The chemical cleaning method is the simplest approach for degreasing oil-based drilling cuttings (ODCs), with the effectiveness of the treatment relying mainly on the selection of the surfactant and the cleaning conditions. However, achieving the standard treatment of ODCs directly using conventional surfactants proves challenging. In light of this, this study introduces a synthesized and purified Gemini surfactant named DCY-1. The structure of DCY-1 was confirmed through Fourier transform infrared (FTIR) and nuclear magnetic resonance (NMR) analyses. The characterization in this article encompasses the use of an interface tension meter, nanoparticle size analysis, scanning electron microscopy, and infrared oil measurement. The critical micelle concentration (CMC) of DCY-1 was determined to be 3.37 × 10–3 mol/L, with a corresponding γcmc value of 37.97 mN/m. In comparison to conventional surfactants, DCY-1 exhibited a larger micelle size of 4.52 nm, approximately 24.52% larger than that of SDS. Moreover, the residual oil rate of 3.96% achieved by DCY-1 was the lowest among the chemical cleaning experimental results. Through a single-factor experiment, the optimal cleaning ability of DCY-1 for ODCs was determined as follows: a surfactant concentration of 3 mmol/L, a temperature of 60 °C, an ODC/liquid mass ratio of 1:4, a cleaning duration of 40 min, and a stirring speed of 1000 rad/min. Under these optimal conditions and after merely two cleaning procedures, the residual oil content of ODCs was reduced to 1.64%, accompanied by a smooth and loose surface structure.
Autor:innen und Institutionen
- College of Chemistry and Chemical Engineering, Southwest Petroleum University, Chengdu 610500, Sichuan, P. R. China.
- Research Institute of Industrial Hazardous Waste Disposal and Resource Utilization, Southwest Petroleum University, Chengdu 610500, Sichuan, P. R. China.
- Institute of Subsurface Energy Systems, Clausthal University of Technology, Clausthal-Zellerfeld 38678, Germany.
- China Railway Eryuan Engineering Group Co, Ltd., Chengdu 610500, Sichuan, P. R. China.
- Industrial Technology Research Institute, Chongqing University, Chongqing 400044, P. R. China.
ORCID-Profile: Yucheng Liu, Zhengmeng Hou
Förderung
- Sichuan Provincial Youth Science and Technology Foundation
- Regional Innovation Cooperation project of Sichuan Province
Zitieren
APA
Yan, X., Liu, Y., Hou, Z., Yuan, L., Yang, J., & Dong, W. (2024). Cleaning Oil-Based Drilling Cuttings with Synthetic Gemini Surfactants. ACS Omega, 9(9), 10488-10497. https://doi.org/10.1021/acsomega.3c08618
Vancouver
Yan X, Liu Y, Hou Z, Yuan L, Yang J, Dong W. Cleaning Oil-Based Drilling Cuttings with Synthetic Gemini Surfactants. ACS Omega. 2024;9(9):10488-10497. doi:10.1021/acsomega.3c08618
BibTeX
@article{Yan2024,
author = {Yan, Xuan and Liu, Yucheng and Hou, Zhengmeng and Yuan, Lina and Yang, Jun and Dong, Wenxin},
title = {Cleaning Oil-Based Drilling Cuttings with Synthetic Gemini Surfactants},
journal = {ACS Omega},
year = {2024},
volume = {9},
number = {9},
pages = {10488--10497},
doi = {10.1021/acsomega.3c08618}
}
EUVIMED