EUVIMEDEUVIMED entdecken
Crossref

Micro-LED-Activated Formaldehyde Sensing via Au Loading-Regulated Interfacial Engineering in Anatase TiO2 Nanofibers

Euichul Shin, Kichul Lee, Yunsung Lim, Minhyun Kim, Donghyuk Kwak, Jehee Yu, Hee Jung Park, Ji-Soo Jang, Inkyu Park, Il-Doo Kim

ACS Nano · 12.11.2026

DOI: 10.1021/acsnano.6c16286 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Nano, online erschienen am 12.11.2026. Verfasst von Euichul Shin und 9 weiteren Autor:innen. Die Arbeit nennt 38 Literaturangaben. Gefördert von: National Research Foundation of Korea, Korea Institute of Marine Science and Technology promotion.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Photoactivated metal-oxide gas sensors reduce the energy demand associated with continuous heating, yet selective detection of volatile organic compounds remains constrained by weak electrical transduction and complex surface oxidation pathways. Here, Au-functionalized anatase TiO2 nanofibers (Au/aTiO2 NFs) were integrated with a 395 nm microlight-emitting diode (LED) for low-power formaldehyde (HCHO) sensing. One-pot electrospinning followed by calcination enabled systematic control of Au loading while preserving the anatase nanofiber architecture. Au loading regulated TiO2 crystallite growth, defect states, dispersion, interfacial Au chemical states, and photoexcited carrier relaxation. At 0.15 wt % Au, finely dispersed Au nanoparticles produced a distinct Au/TiO2 interfacial environment and carrier-relaxation behavior, whereas higher loadings induced nanoparticle aggregation and additional nonradiative energy-loss pathways. Under UV micro-LED illumination at 2.63 mW, the optimized sensor exhibited a response of 1093 toward 1 ppm of HCHO, an estimated detection limit of 4.9 ppb, and stable operation over 40 consecutive cycles. Density functional theory calculations further supported the loading-dependent selectivity, showing that changes in the local Au environment selectively modify HCHO adsorption and bond reconstruction. These results identify local Au-site density as a key design parameter governing interfacial reactivity and molecular selectivity in low-power photoactivated gas sensing.

Förderung

  • National Research Foundation of Korea
  • Korea Institute of Marine Science and Technology promotion

Zitieren

APA

Shin, E., Lee, K., Lim, Y., Kim, M., Kwak, D., Yu, J., Park, H. J., Jang, J., Park, I., & Kim, I. (2026). Micro-LED-Activated Formaldehyde Sensing via Au Loading-Regulated Interfacial Engineering in Anatase TiO2 Nanofibers. ACS Nano. https://doi.org/10.1021/acsnano.6c16286

Vancouver

Shin E, Lee K, Lim Y, Kim M, Kwak D, Yu J, et al. Micro-LED-Activated Formaldehyde Sensing via Au Loading-Regulated Interfacial Engineering in Anatase TiO2 Nanofibers. ACS Nano. 2026. doi:10.1021/acsnano.6c16286

BibTeX
@article{Shin2026,
  author = {Shin, Euichul and Lee, Kichul and Lim, Yunsung and Kim, Minhyun and Kwak, Donghyuk and Yu, Jehee and Park, Hee Jung and Jang, Ji-Soo and Park, Inkyu and Kim, Il-Doo},
  title = {Micro-LED-Activated Formaldehyde Sensing via Au Loading-Regulated Interfacial Engineering in Anatase TiO2 Nanofibers},
  journal = {ACS Nano},
  year = {2026},
  doi = {10.1021/acsnano.6c16286}
}
Kostenlos starten →