EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fully Printed Ionic Diodes from Polymerizable Ionic Liquids

Alexander Q Kane iD, Eric Yang iD, Ryan L Truby iD

ACS Nano · 11.08.2026 · 20 (31) · 21953-21964

DOI: 10.1021/acsnano.6c06135 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Nano, online erschienen am 27.07.2026. Verfasst von Alexander Q Kane und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Science and Engineering, Northwestern University, Evanston, Illinois60208, United States. Die Arbeit nennt 68 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Division of Materials Research, Air Force Office of Scientific Research, International Institute for Nanotechnology, Northwestern University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Soft ionic diodes (SIDs) comprising p- and n-type polyelectrolytes are fundamental components of bioinspired iontronic devices. However, traditional ionic diode fabrication techniques require low-throughput, manual processes to interface electrodes and electrolytes and are typically limited to producing planar geometries. Moreover, hydrogels commonly used as SID electrolytes lose water over time, which leads to device instability and loss of performance. In this work, we present a method for fully 3D printing ionic diodes from solvent-free, polymerizable ionic liquids (pILs) that enables rapid and scalable manufacturing of SIDs. Four inks, including p- and n-type electrode and electrolyte inks, are used to print SIDs with 2D to 3D geometries and rectification ratios of up to 46. The geometry-, scan rate-, and time-dependent performance of SIDs are characterized via cyclic voltammetry and chronoamperometry. Leveraging the flexibility of 3D printing, we demonstrate current and voltage scaling relationships in multidiode arrays printed in parallel or series, respectively. We also highlight a dense multidiode crossbar array (≈100 SIDs/cm2) that can be quickly and uniquely achieved with our 3D printing approach. We anticipate the materials and methods reported in this work will enable opportunities for fabricating ionic diodes and multifunctional iontronic devices critical to advancing applications in bioelectronics, neuromorphics, and soft robotics.

Schlagwörter

Stichwörter der Autor:innen

3D printingionic diodesiontronicspoly(ionic liquids)rectification

Autor:innen und Institutionen

  • Department of Materials Science and Engineering, Northwestern University, Evanston, Illinois60208, United States.
  • Department of Mechanical Engineering, Northwestern University, Evanston, Illinois60208, United States.

ORCID-Profile: Alexander Q Kane, Eric Yang, Ryan L Truby

Förderung

  • Division of Materials Research
  • Air Force Office of Scientific Research
  • International Institute for Nanotechnology, Northwestern University
  • Biological Technologies Office

Zitieren

APA

Kane, A. Q., Yang, E., & Truby, R. L. (2026). Fully Printed Ionic Diodes from Polymerizable Ionic Liquids. ACS Nano, 20(31), 21953-21964. https://doi.org/10.1021/acsnano.6c06135

Vancouver

Kane AQ, Yang E, Truby RL. Fully Printed Ionic Diodes from Polymerizable Ionic Liquids. ACS Nano. 2026;20(31):21953-21964. doi:10.1021/acsnano.6c06135

BibTeX
@article{Kane2026,
  author = {Kane, Alexander Q and Yang, Eric and Truby, Ryan L},
  title = {Fully Printed Ionic Diodes from Polymerizable Ionic Liquids},
  journal = {ACS Nano},
  year = {2026},
  volume = {20},
  number = {31},
  pages = {21953--21964},
  doi = {10.1021/acsnano.6c06135}
}
Kostenlos starten →