EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Additive Manufacturing of Customized Flexible Wearable Sensors for Sweat Analysis with Bespoke, Low-Cost Conductive TPU

Mayane S Carvalho, Elena Bernalte, Ana C M Oliveira iD, Eduardo M Richter iD, Rodrigo A A Muñoz iD, Robert D Crapnell iD, Craig E Banks iD

ACS Measurement Science Au · 17.12.2025 · 5 (6) · 842-856

DOI: 10.1021/acsmeasuresciau.5c00095 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Measurement Science Au, online erschienen am 26.09.2025. Verfasst von Mayane S Carvalho und 6 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Science and Engineering, Manchester Metropolitan University, Dalton Building, Chester Street, Manchester M1 5GD, Great Britain. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 85 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Funda??o de Amparo ? Pesquisa do Estado de Minas Gerais, Conselho Nacional de Desenvolvimento Cient?fico e Tecnol?gico, HORIZON EUROPE Framework Programme.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The development of wearable technology that is non-invasive, customizable, comfortable for the user, and able to transmit data to healthcare providers from remote and rural locations has the potential to revolutionize the healthcare sector and aligns with key United Nations Sustainable Development Goals. In this work, bespoke conductive filaments based on thermoplastic polyurethane (TPU) incorporating different ratios of carbon black (CB) and graphite (GRT) were developed, for the first time, via melt extrusion for additive manufacturing of flexible, wearable electrochemical sensors. Eight formulations were systematically evaluated in terms of morphology, electrical resistance, wettability, and electrochemical behavior. The hybrid composition containing 20 wt% CB and 20 wt% GRT demonstrated the best balance between conductivity, mechanical flexibility, printability, and electrochemical activity, while producing a 45% saving in material cost. Surface activation through (electro)-chemical treatment and mechanical polishing significantly improved the electroactive surface area and heterogeneous electron transfer rate, especially for GRT-containing electrodes. The optimized electrode exhibited the highest k 0 and A e values and was integrated into a fully printed three-electrode wristband for non-invasive detection of uric acid (UA) in artificial sweat. Differential pulse voltammetry enabled reliable detection of UA in the 2.5-100.0 μmol L-1 range with a limit of detection of 1.3 μmol L-1 and recovery rates up to 99.7%. The sensor also demonstrated high selectivity against typical sweat interferents such as urea, glucose, and tyrosine. These findings support the potential of additively manufactured carbon-based TPU electrodes for application in wearable sensing platforms for real-time biomarker monitoring.

Schlagwörter

Stichwörter der Autor:innen

Additive manufacturingCarbon blackFlexible electrodesGraphiteThermoplastic polyurethane (TPU)Uric acidWearable device

Autor:innen und Institutionen

  • Faculty of Science and Engineering, Manchester Metropolitan University, Dalton Building, Chester Street, Manchester M1 5GD, Great Britain.
  • Institute of Chemistry, Federal University of Uberlândia, 38400-902 Uberlândia, Minas Gerais, Brazil.

ORCID-Profile: Ana C M Oliveira, Eduardo M Richter, Rodrigo A A Muñoz, Robert D Crapnell, Craig E Banks

Förderung

  • Funda??o de Amparo ? Pesquisa do Estado de Minas Gerais
  • Conselho Nacional de Desenvolvimento Cient?fico e Tecnol?gico
  • HORIZON EUROPE Framework Programme
  • Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior

Zitieren

APA

Carvalho, M. S., Bernalte, E., Oliveira, A. C. M., Richter, E. M., Muñoz, R. A. A., Crapnell, R. D., & Banks, C. E. (2025). Additive Manufacturing of Customized Flexible Wearable Sensors for Sweat Analysis with Bespoke, Low-Cost Conductive TPU. ACS Measurement Science Au, 5(6), 842-856. https://doi.org/10.1021/acsmeasuresciau.5c00095

Vancouver

Carvalho MS, Bernalte E, Oliveira ACM, Richter EM, Muñoz RAA, Crapnell RD, et al. Additive Manufacturing of Customized Flexible Wearable Sensors for Sweat Analysis with Bespoke, Low-Cost Conductive TPU. ACS Measurement Science Au. 2025;5(6):842-856. doi:10.1021/acsmeasuresciau.5c00095

BibTeX
@article{Carvalho2025,
  author = {Carvalho, Mayane S and Bernalte, Elena and Oliveira, Ana C M and Richter, Eduardo M and Muñoz, Rodrigo A A and Crapnell, Robert D and Banks, Craig E},
  title = {Additive Manufacturing of Customized Flexible Wearable Sensors for Sweat Analysis with Bespoke, Low-Cost Conductive TPU},
  journal = {ACS Measurement Science Au},
  year = {2025},
  volume = {5},
  number = {6},
  pages = {842--856},
  doi = {10.1021/acsmeasuresciau.5c00095}
}
Kostenlos starten →