EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Morphology and Thermal Tuning of α-CuV2O6 Photoanodes for Optimized Photoelectrochemical Performance

Mohammad Arham Shamim iD, Abhishek Rawat iD, Deepika V Karade, Chuzhong Zhang, Clement U Nwokeji, Efstathios I Meletis, Krishnan Rajeshwar iD

ACS Materials Au · 11.11.2026 · 6 (6) · 1495-1503

DOI: 10.1021/acsmaterialsau.6c00148 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Materials Au, online erschienen am 17.09.2026. Verfasst von Mohammad Arham Shamim und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemistry & Biochemistry, The University of Texas at Arlington, Arlington, Texas 76019, United States. Die Arbeit nennt 24 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: National Science Foundation UTA/NU Partnership for Research and Education in Materials.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Microstructural engineering provides an effective strategy to enhance semiconductor photoelectrodes without modifying the intrinsic electronic structure. Here, phase-pure α-CuV2O6 photoanodes were mechanically and thermally tuned to control particle size, film morphology, and interfacial charge-transfer kinetics for optimal photoelectrochemical (PEC) water oxidation. Mechanical grinding reduced the average particle size from micrometer to submicrometer dimensions while preserving the triclinic lattice, enabling uniform, high-coverage films with unchanged optical bandgaps (Eg ≈ 1.8–1.9 eV). Systematic optimization of the number of spray-coating cycles and anneal temperature afforded 60 spray cycles and 450 °C as the optimal conditions, where improved densification and maximized electrochemically active surface area enhanced carrier utilization and suppressed interfacial recombination simultaneously. The optimized photoanodes delivered a photocurrent density of 1.70 mA cm–2 at 1.80 V vs RHE, which is the record maximum photocurrent reported thus far for α-CuV2O6 photoelectrodes experimentally. Transient photocurrent analysis confirmed that performance gains originated primarily from reduced surface recombination rather than changes in optical absorption or interfacial energetics. These new findings demonstrate that morphology-driven kinetic control offers a simple, scalable route to unlock the latent PEC activity of copper vanadate photoanodes and elevate their performance levels closer to theoretical expectations.

Schlagwörter

Stichwörter der Autor:innen

charge carriersgrain sizephotoabsorptionphotoresponsesemiconductor

Autor:innen und Institutionen

  • Department of Chemistry & Biochemistry, The University of Texas at Arlington, Arlington, Texas 76019, United States.
  • Department of Material Science and Engineering, The University of Texas at Arlington, Arlington, Texas 76019, United States.

ORCID-Profile: Mohammad Arham Shamim, Abhishek Rawat, Krishnan Rajeshwar

Förderung

  • National Science Foundation UTA/NU Partnership for Research and Education in Materials

Zitieren

APA

Shamim, M. A., Rawat, A., Karade, D. V., Zhang, C., Nwokeji, C. U., Meletis, E. I., & Rajeshwar, K. (2026). Morphology and Thermal Tuning of α-CuV2O6 Photoanodes for Optimized Photoelectrochemical Performance. ACS Materials Au, 6(6), 1495-1503. https://doi.org/10.1021/acsmaterialsau.6c00148

Vancouver

Shamim MA, Rawat A, Karade DV, Zhang C, Nwokeji CU, Meletis EI, et al. Morphology and Thermal Tuning of α-CuV2O6 Photoanodes for Optimized Photoelectrochemical Performance. ACS Materials Au. 2026;6(6):1495-1503. doi:10.1021/acsmaterialsau.6c00148

BibTeX
@article{Shamim2026,
  author = {Shamim, Mohammad Arham and Rawat, Abhishek and Karade, Deepika V and Zhang, Chuzhong and Nwokeji, Clement U and Meletis, Efstathios I and Rajeshwar, Krishnan},
  title = {Morphology and Thermal Tuning of α-CuV2O6 Photoanodes for Optimized Photoelectrochemical Performance},
  journal = {ACS Materials Au},
  year = {2026},
  volume = {6},
  number = {6},
  pages = {1495--1503},
  doi = {10.1021/acsmaterialsau.6c00148}
}
Kostenlos starten →