Three-Dimensional Printing of Polycaprolactone Scaffolds with Multiscale Porosity for Bone Tissue Engineering
ACS Biomaterials Science & Engineering · 2026
DOI: 10.1021/acsbiomaterials.6c00276 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Biomaterials Science & Engineering, 2026. Verfasst von Mikaela Kutrolli und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Biomedical Engineering, School of Dental Medicine, University of Connecticut Health Center, Farmington, CT06030, United States. Hauptthemen laut MEDLINE: Polyesters, Tissue Scaffolds, Printing, Three-Dimensional, Tissue Engineering. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 69 Literaturangaben. Gefördert von: U.S. Department of Defense, NIBIB NIH HHS, National Institute of Biomedical Imaging and Bioengineering.
Abstract (Originalsprache)
Extrusion-based three-dimensional printing enables the fabrication of patient-specific scaffolds. Polycaprolactone (PCL)-based scaffolds have been widely used for the treatment of bone defects. However, extruded filaments are typically nonporous, which can prolong their degradation, limit cell adhesion and infiltration, and therefore interrupt normal tissue regeneration. Here, we present a simple and scalable method to generate polymeric scaffolds with hierarchical porosity by incorporating sacrificial sugar particles in a printable PCL ink. Microstructural analysis by SEM demonstrates an average pore size of around 10 μm with increased pore density at higher porogen fractions. Porous PCL improved apparent wettability and protein adsorption, accelerated hydrolytic degradation by more than five-fold, and enabled tunable mechanical properties. Printability testing shows improved filament stability and reduced fusion at higher porogen loading, enabling significantly higher printing resolution. In vitro evaluation demonstrates enhanced early preosteoblast attachment on porous scaffolds (>three-fold), without loss of cytocompatibility. Importantly, porous scaffolds support osteogenic differentiation of the cells and mineralization. This study provides a practical framework for creating intrafilamentary porosity into 3D-printed PCL scaffolds with improved surface-mediated biological performance.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Biomedical Engineering, School of Dental Medicine, University of Connecticut Health Center, Farmington, CT06030, United States.
- Department of Mechanical & Aerospace Engineering, Old Dominion University, Norfolk, VA23529, United States.
Förderung
- U.S. Department of Defense
- NIBIB NIH HHS
- National Institute of Biomedical Imaging and Bioengineering
Zitieren
APA
Kutrolli, M., Pereira, N. S., Ghanbariamin, D., Arnold, K. M., Deymier, A., Samandari, M., & Tamayol, A. (2026). Three-Dimensional Printing of Polycaprolactone Scaffolds with Multiscale Porosity for Bone Tissue Engineering. ACS Biomaterials Science & Engineering. https://doi.org/10.1021/acsbiomaterials.6c00276
Vancouver
Kutrolli M, Pereira NS, Ghanbariamin D, Arnold KM, Deymier A, Samandari M, et al. Three-Dimensional Printing of Polycaprolactone Scaffolds with Multiscale Porosity for Bone Tissue Engineering. ACS Biomaterials Science & Engineering. 2026. doi:10.1021/acsbiomaterials.6c00276
BibTeX
@article{Kutrolli2026,
author = {Kutrolli, Mikaela and Pereira, Noah S and Ghanbariamin, Delaram and Arnold, Katherine M and Deymier, Alix and Samandari, Mohamadmahdi and Tamayol, Ali},
title = {Three-Dimensional Printing of Polycaprolactone Scaffolds with Multiscale Porosity for Bone Tissue Engineering},
journal = {ACS Biomaterials Science & Engineering},
year = {2026},
doi = {10.1021/acsbiomaterials.6c00276}
}
EUVIMED