EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Support-Enabled 3D Printing of Complex Anisotropic Hydrogel Structures Using Cellulose-Based Inks: Pathways Toward Biomimetic Human Aorta Models

Daniel Pint iD, Tobias Steindorfer, Florian Lackner, Tamilselvan Mohan iD, Heidrun Gruber-Woelfler iD, Rupert Kargl iD, Karin Stana Kleinschek iD

ACS Biomaterials Science & Engineering · 2026

DOI: 10.1021/acsbiomaterials.5c02127 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Biomaterials Science & Engineering, 2026. Verfasst von Daniel Pint und 6 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Chemistry and Technology of Biobased System (IBioSys), Graz University of Technology, Stremayrgasse 9, 8010 Graz, Austria. Hauptthemen laut MEDLINE: Cellulose, Printing, Three-Dimensional, Ink, Hydrogels. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Federal provinces: Styria through SFG, Upper Austria, Vorarlberg, Austrian Research Promotion Agency (FFG).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Three-dimensional (3D) printing of hydrogels has enabled new directions in biomedical engineering, soft material design, and biofabrication. However, unsupported hydrogel inks often collapse under their own weight or deform during printing, limiting achievable geometries. Herein, we present a reproducible, standardized support system combining a nanofibrillated cellulose/sodium alginate (NFC/ALG) structural ink with a cellulose-based sacrificial support ink composed of NFC, hydroxyethyl cellulose (HEC), and CaCl2. The process operates in open air, in contrast to immersion-bath methods such as FRESH, and uses a dissolvable support that locally stabilizes and initiates cross-linking of deposited filaments without submersion. Detailed protocols are provided for ink preparation, cartridge loading, direct ink writing (DIW) parameters, postprinting cross-linking, and support dissolution. Quantitative validation using tubular models shows that unsupported tubes collapse before 50 mm height, whereas supported tubes remain upright and stable. Surface fidelity is substantially improved by reducing layer height from 840 to 420 μm, yielding watertight prints. Demonstrations of complex geometries, including an anatomical aorta, DNA double helix, and the benchmark 3D Benchy model, confirm the method’s capability. Support dissolution in 30 mM CaCl2 occurs over approximately 3 days, ensuring stability during cross-linking and handling. Compared with other sacrificial strategies, this approach is inexpensive, cellulose-based, and relies on mild ionic cross-linking compatible with future cell-laden systems. This work provides a robust and accessible hydrogel engineering protocol, supporting stable and high-fidelity DIW of complex anisotropic structures.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CellulosePrinting, Three-DimensionalInkHydrogelsAortaBiomimetic MaterialsHumansAlginatesCalcium ChlorideAnisotropyHexuronic AcidsBiomimetics

Stichwörter der Autor:innen

3D bioprintingalginateanisotropic printingcellulose bioinksdirect ink writinghydrogelhydroxyethyl cellulosenanocellulosesacrificial support

Substanzen

CelluloseHydrogelsAlginatesCalcium ChloridehydroxyethylcelluloseHexuronic Acids

Autor:innen und Institutionen

  • Institute of Chemistry and Technology of Biobased System (IBioSys), Graz University of Technology, Stremayrgasse 9, 8010 Graz, Austria.
  • Institute of Process and Particle Engineering, Graz University of Technology, Inffeldgasse 13, 8010 Graz, Austria.

ORCID-Profile: Daniel Pint, Tamilselvan Mohan, Heidrun Gruber-Woelfler, Rupert Kargl, Karin Stana Kleinschek

Förderung

  • Federal provinces: Styria through SFG, Upper Austria, Vorarlberg
  • Austrian Research Promotion Agency (FFG)

Zitieren

APA

Pint, D., Steindorfer, T., Lackner, F., Mohan, T., Gruber-Woelfler, H., Kargl, R., & Stana Kleinschek, K. (2026). Support-Enabled 3D Printing of Complex Anisotropic Hydrogel Structures Using Cellulose-Based Inks: Pathways Toward Biomimetic Human Aorta Models. ACS Biomaterials Science & Engineering. https://doi.org/10.1021/acsbiomaterials.5c02127

Vancouver

Pint D, Steindorfer T, Lackner F, Mohan T, Gruber-Woelfler H, Kargl R, et al. Support-Enabled 3D Printing of Complex Anisotropic Hydrogel Structures Using Cellulose-Based Inks: Pathways Toward Biomimetic Human Aorta Models. ACS Biomaterials Science & Engineering. 2026. doi:10.1021/acsbiomaterials.5c02127

BibTeX
@article{Pint2026,
  author = {Pint, Daniel and Steindorfer, Tobias and Lackner, Florian and Mohan, Tamilselvan and Gruber-Woelfler, Heidrun and Kargl, Rupert and Stana Kleinschek, Karin},
  title = {Support-Enabled 3D Printing of Complex Anisotropic Hydrogel Structures Using Cellulose-Based Inks: Pathways Toward Biomimetic Human Aorta Models},
  journal = {ACS Biomaterials Science & Engineering},
  year = {2026},
  doi = {10.1021/acsbiomaterials.5c02127}
}
Kostenlos starten →